Sanyo VCC-HD2100 - Full HD 1080p Network Camera Скачать руководство пользователя страница 7

Страница: 7 / 118

Operation

Associated button and use

Equivalent network operation

screen

Restarting camera

Press the RESET button.

OPTION SETTINGS (CAMERA
REBOOT)

Restoring factory default

settings

Press the NEAR and SET buttons

simultaneously.

OPTION SETTINGS (FACTORY

DEFAULT)

Restoring factory default

back focus position

Press the NEAR and FAR buttons
simultaneously.

CAMERA SETTINGS (FOCUS
ASSIST)

Resetting login password

Press the FAR and SET buttons

simultaneously.

USER SETTINGS

Adjusting focus

For details, refer to the “Lens
Adjustment” section.

CAMERA SETTINGS (FOCUS
ASSIST/IRIS SETTINGS)

Adjusting iris

Viewing Firmware Version

For details, refer to the “Viewing

Firmware Version” section.

OPTION SETTINGS (FIRMWARE

UPDATE)

This bracket may be attached to either the top or bottom face of the camera depending on the installation
environment.

For bracket installation, be sure to use the longer screws supplied.

Install the camera securely to a durable location, taking into account the total weight of the camera
mount (commercially available) and the camera.

Introduction 7/17

Содержание VCC-HD2100 - Full HD 1080p Network Camera























































































































Результаты поиска

Содержание VCC-HD2100 - Full HD 1080p Network Camera

Отзывы:

Похожие инструкции для VCC-HD2100 - Full HD 1080p Network Camera

Бренды по названию

Популярные бренды

Sanyo VCC-HD2100 - Full HD 1080p Network Camera, Руководство пользователя

Результаты поиска

Содержание VCC-HD2100 - Full HD 1080p Network Camera

Отзывы:

Похожие инструкции для VCC-HD2100 - Full HD 1080p Network Camera

Бренды по названию

Популярные бренды