Sanyo PLV-HD10, Руководство по обслуживанию, Страница: 78 / 178

S 0 – Temperature Monitor Indication
– 0 LM76 (Temp) Monitor Temp. Sensor (Intake) – – –
– 1 LM76 (Temp) Monitor Temp. Sensor (Inner) – – –
– 2 Thermistor Monitor Temp. Thermistor (Inner) – – –
S 1 – Pressure Monitor Indication
– 0 MPXA4114A(Pressure) Monitor Pressure Sensor – – –
S 7 – Power Fail Monitor
– 0 Main (High 8Bit) Main Power fail (L : Abnormality) – – –
– 1 Main (Low 8Bit) Main Power fail (L : Abnormality) – – –
– 2 Sub Power Sub Power P-fail (L : Abnormality) – – –
– 3 100V 100V A/D Reading – – –
– 4 Fan_D Fan_D Power fail – – –
S 8 – Frequency Counter Monitor
– 0 SW FPGA No Signal – – –
– 1 SW FPGA H Counter – – –
– 2 SW FPGA V Counter – – –
S 9 – Lamp Status Monitor
– 0 Lighting Lamp Number – – –
S 10 – RS232C Set
– 0 Baud rate RS232C Baud rate (0 : 9600 / 1 : 19200) 0 / 1 1 –
– 1 RTS/CTS Flow Control RS232C RTS/CTS Flow Control (0 : Disable / 1: Enable) 0 / 1 0 –
– 2 CTS Timeout Second RS232C CTS Timeout 0 ~ 255 0 –
– 3 Serial Address Individual address in RS–232C chain connection 0 ~ 999 1 –
S 11 – LAN Setting (Option)
– 0 LAN Card Switch LAN (0 : Disable / 1: Enable) 0 / 1 0 –
S 20 – Logo On/Off
– 0 Logo On/Off (0 : Menu Operation / 1 : Prohibition) 0 / 1 0 –
S 30 – Color Shade Compensation
– 0 Compensation On/Off (0 : Off / 1 : On) 0 / 1 1 –
S 40 – Dimmer Control
– 0 Dimmer On/Off (0 : Menu Operation / 1 : Off) 0 / 1 1 –
– 1 Dimmer Level (0 : 200W ~ 15 : 250W) 0 ~ 15 15 –
S 50 – Auto Picture Control
– 0 Auto Picture On/Off (0 : Menu Operation / 1 : Off) 0 / 1 1 –
S 110 – Lamp Total Lighting Time
– 0 Lamp 1 Lamp 1 Total Lighting Time – 0 –
– 1 Lamp 2 Lamp 2 Total Lighting Time – 0 –
– 2 Lamp 3 Lamp 3 Total Lighting Time – 0 –
– 3 Lamp 4 Lamp 4 Total Lighting Time – 0 –
S 111 – Lamp On Time
– 0 Lamp 1 Lamp 1 Lighting Time – 0 –
– 1 Lamp 2 Lamp 2 Lighting Time – 0 –
– 2 Lamp 3 Lamp 3 Lighting Time – 0 –
– 3 Lamp 4 Lamp 4 Lighting Time – 0 –
S 112 – Lamp Config
– 0 Lamp Config Change Lamp Monitor Time Set (Step : 500h) 1000 ~ 8000 1500 –
S 120 – RC KEY Disable
– 0 RC Zoom & Focus Only 0 : Enable / 1 : Disable 0 / 1 0 –
– 1 RC / KEY All 0 : Enable / 1 : RC Disable / 2 : KEY Disable 0 / 1 / 2 0 –
– 2 Process after Power Fail 0 : Not Recover by KEY / 1 : Recover by KEY 0 / 1 0 –
S 140 – Fan Output Level
– 0 Fan A Min (
✽
) Fan A Driving Voltage Adj. at TP7611 0 ~ 255 190 –
– 1 Fan A Max (
✽
) Fan A Driving Voltage Adj. at TP7611 0 ~ 255 35 –
– 2 Fan C Min (
✽
) Fan C Driving Voltage Adj. at TP2661 0 ~ 255 215 –
– 3 Fan C Max (
✽
) Fan C Driving Voltage Adj. at TP2661 0 ~ 255 30 –
– 4 Fan B Min (
✽
) Fan B Driving Voltage Adj. at TP2671 0 ~ 255 205 –
– 5 Fan B Max (
✽
) Fan B Driving Voltage Adj. at TP2671 0 ~ 255 25 –
– 6 Fan D Min (
✽
) Fan D Driving Voltage Adj. at TP2631 0 ~ 255 96 –
– 7 Fan D Max (
✽
) Fan D Driving Voltage Adj. at TP2631 0 ~ 255 43 –
S 141 – Fan Output Level
– 0 Fan Output Level 0 : Max / 2 : Auto / 3 : Min 0 ~ 3 2 –
S 150 – Factory Set (Reset)
– 0 Factory Set Do not touched. Available at No.10 caution : Important! Do not attempt. 0 ~ 10 0 –
–78–
Group
No.
Data
Range
Initial Value
Function
Item
No.
ITEM
PLV-HD10
PLV-HD100
CAUTION : These initial values are the reference data written from the CPU ROM to the memory IC when the new
memory IC replaced. The adjustment items indicated with “
✽
” are required to readjust following to the
“Electrical adjustments”. Other items should be used with the initial data value.
●
Service Adjustment Data table (Factory Set Data List)
Electrical Adjustments