background image

- 14 -  

Replacement of Suspension Rod Ass y:

 

                                                     

Lead Wire connector for water supply Valve

 

(1) 

Move the insulation tube. 

(2) 

To  remove  the  connector  from  water  supply 
valve, pull it while pressing the Projection in the 
middle with your nail to unlock. 

Do  not  pull  it  by  force  without  unlocking, 
otherwise the Lead Wire may be torn off. 

When  reconnecting  the  Connector,  make  sure 
that  it  is  locked  firmly  by  pulling  it  slightly  after 
connecting.  

(3) 

Fix the Insulation Tube.  

      

When you have to replace a suspension rod complete, please replace the all of four  Suspension Rod 
Assembly. 

There are four types of Suspension Rod Complete:     

(1)

 

Remove the screws which are seemed on

 

Top plate, follow the steps of  Replacing top plate .

 

(2) 

Lay  the  washer  down  left  or  right  suitably  on  the  floor  (It  is  necessary  to  have  a  soft  cloth  or  blanket  to 
protect the washer). 

(3) 

Remove the Top Plate. 

(4) 

From bottom of Outer Tub, push the Suspension Rod Ass y up until it raises from suspension base. 

(5) 

After removing the Stopping Pin, pull out the Suspension Rod Ass y from bottom of Frame. 

(6) 

Follow  the  steps  above  in  the  reverse  order  when  you  want  to  assemble  them  again  with  a  new 
Suspension Rod Ass y. 

Lead Wire

 

Projection

 

Insulation Tube

 

Connector

 

Front

  

    

  

At the non- motor side:

 

 (In the corner of front side and right side)      

1 Set  (Service Code: 617-259-7102)

 

 

  

At the non- motor side: 

 

1 Set  (Service Code: 617-259-7188) 

 

Left

Right

 

Motor

 

Back

 

  

At the motor side: 

 

1 Set  (Service Code: 617-259-7195) 

 

    At the motor side:

 

  (In the corner of front side and left side)     
   1 Set  (Service Code: 617-259-7119)

 

 

Содержание ASW U1100T






























Отзывы: