Sanyo Denki SANMOTION F5 Скачать руководство пользователя страница 108

Страница: 108 / 112

1. Do not use the product in an explosive, flammable or corrosive

atmosphere, watery place or near a combustible material. Doing so
may cause injury or fi re.

2. Have a person with expert knowledge for performing the transportation

,placement,wiring, operation, maintenance or inspection of the product.
Without such knowledge, it may cause an electric shock, injury or fi re.

3. Do not work for wiring, maintenance servicing or inspection with the

electric power on. Perform either of those five minutes after turning
the power off, or otherwise, it may cause an electric shock.

4. When the protective functions of the product is activated, turn the power

off immediately and eliminate the cause. If continuing the operation
without eliminating the cause, the product may operate improperly and
cause injury or a breakdown of the system devices.

5. Stepping motor may run out of order at the operating and stopping

occasions, depending on the magnitude of the load. Put the product
into use after confirming with the adequate trial test operation in the
maximum load conditions that the product performs reliable operation.
Doing otherwise may cause a breakdown of the system. (Should the
product run out of order in the use to drive upward/downward, it may
cause a fall of the load.)

6. Do not touch the internal parts of the driver. Doing so may cause an

electric shock.

7. Do not connect the stepping motor directly with the commercial power

outlet. Doing so may cause an electric shock, injury or fi re. The power
shall be supplied to the stepping motor through the driving circuit.

8. Use the electric power source within the rated input voltage. Using

otherwise may cause fi re or an electric shock.

9. Connect the driver and stepping motor to the ground. Using without

grounding may cause an electric shock.

10. Do not harm, forcibly put a stress, or load a heavy article on the cable or

get it caught between the articles. Doing so may cause an electric shock.

11. Perform wiring with the power cable as instructed by the wiring

diagram or the Operation Manual. Doing otherwise may cause an
electric shock or fi re.

12. Be sure not to touch the rotating part of the stepping motor during its

operation. Touching it may cause injury.

13. Neither reach or touch the electric terminals while electric power is on.

Doing so may cause an electric shock.

14. Never disconnect any of the connectors while electric power is on. Doing

so may cause an electric shock and corruption.

1. Prior to placement, operation, maintenance servicing or inspection, be sure

to read the Operation Manual and follow the instructions to perform those.
Failure to follow the instructions may cause an electric shock, injury or fi re.

2. Do not use the driver or the stepping motor outside the specified

conditions.

Doing so may cause an electric shock, injury or fi re.

3. Do not insert a fi nger or a thing into the opening of the product. Doing

so may cause an electric shock, injury or fi re.

4. Do not use the damaged driver or stepping motor. Doing so may cause

injury, fi re or the like.

5. Use the driver and stepping motor in the designated combination. Using

otherwise may cause fi re or a trouble.

6. Be careful that the temperature rises in the operating driver, stepping

motor or peripheral devices. Failure to be careful may cause a burn.

7. Unpack while confi rming the ceiling. Failure to do so may cause injury.
8. Confi rm if the product is the one having been ordered. Installing an

incorrect product may cause a breakdown.

9. Do not perform measurement of the insulation resistance or withstand

insulation voltage of the product. Doing so may cause a breakdown.
Instead, contact with us for such inspection.

10. Perform wiring conforming to the technical standards of electric facility

or the internal rule. Doing otherwise may cause burning or fi re.

11. Ensure that wiring has been correctly done. Operating without correct wiring

may cause the stepping motor to run out of control and result in injury.

12. Take insulation process for the attached condenser or the external resistance

connection terminals. Failure to do so may cause an electric shock.

13. Do not climb or attach a heavy article on the product. Doing so may cause injury.
14. Neither block nor stuff the aspiration/exhaust vent with a foreign particle.

Doing so may cause fi re.

15. Follow the instructions for the direction to place. Failure to do so may

cause a trouble.

16. Keep a distance as instructed by the Operation Manual for the driver from

the inner surface of the control console or other devices. Failure to do so
may cause a trouble.

17. Place the product with a great care so as to prevent from the danger such

as a tumble or a turnover.

18. Mount the product on an incombustible material such as metal. Doing

otherwise may cause fi re.

19. Confi rm the rotating direction before connecting with the mechanical

device. Failure to do so may cause injury or a breakdown.

20. Do not touch the motor output spindle (including the key slot and gears)

with a bare hand. Doing so may cause injury.

21. The stepping motor is not equipped with any protective device. Take

protective measures using an over-current protective relay, a ground
fault interrupter, a protective device from excess temperature, and an
emergency stopping device. Failure to do so may cause injury or fi re.

22. Do not touch the product for a period after the power is on or has been turned

off, since the driver and stepping motor remain in the high temperature. Doing
so may cause burns. Especially the temperature rises considerably of the
stepping motor depending on the operating conditions. Use the motor on the
condition so that its surface temperature becomes 100

C or under

23. Stop the operation immediately when an emergency occurs. Failure to

do so may cause an electric shock, injury or fi re.

24. Do not change adjustment to an extreme, for such a change results in the

unstable operation. Doing so may cause injury.

25. When conducting the trial operation, make the stepping motor fixed

fi rmly, and confi rm the operation by disconnecting with the mechanical
system before connecting with it. Failure to do so may cause injury.

26. When the alarm has been activated, eliminate the cause and ensure the

safety to resume operation. Failure to do so may cause injury.

27. When the electric power recovers after the momentary interruption, do

not approach the devices because the system may re-start operation by
itself. (Set the system so as to secure the safety even when it re-start on
such occasion.) Failure to do so may cause injury.

28. Confi rm that the electric power supply is all proper conforming to the

specifi cations. Failure to do so may cause a trouble.

29. The brake mechanism of the motor with the electro-magnetic brake is to

hold the movable section and the motor position. Do not use it as a safety
measure, or doing so may cause the breakdown of the system.

30. Fix the key firmly when operating the motor with key individually.

Failure to do so may cause injury.

31. Be careful when performing maintenance services or inspection about

the temperature which rises highly in the driver and stepping motor
frame. Failure to do so may cause burns.

32. It is recommended to replace the electrolytic condenser of the driver

with a new one for securing the preventive measure after using for 5
years, the expected life in the average 40

C. The expected life of the

fuse and cooling fan motor is 10 years in the average 40

C. Thus, the

periodical replacement is recommended.

33. Contact with us for repair. If the product is disassembled by the user,

it may put it out of action.

34. Handle the product with care during transportation so as to prevent from

the danger such as a tumble or a turnover.

35. Do not hold with the cable or the motor spindle. Doing so may cause a

trouble or injury.

36. When scrapping the driver or stepping motor, treat it for the general

industrial waste.

PROHIBITED

1. Avoid the place exposed to rain or water drops, or in an environment with

hazardous gas or liquid for storing the product. Failure to do so may cause
a trouble.

2. Do not assemble or repair the product. Doing so may cause fire or an

electric shock.

3. Do not remove the rating plate.

COMPULSORY

1. Store the product within the specifi ed conservation temperature and

humidity in the place not exposed to the sun beam.

2. If the driver has been stored for a long period (3 years or longer for a guide),

consult with us. The capacitance may have decreased with the electrolytic
condenser due to the long period storage, and it may cause a trouble.

3. Install an external emergency stop circuit to turn the power off for the

instant halt of operation.

4. Put the product into operation in the specifi ed ambient temperature and

humidity.

5. Excess loading of the product on the carrier may cause the load to fall in

pieces. Follow the instructions given outside the package.

108

Содержание SANMOTION F5

















































































































Результаты поиска

Содержание SANMOTION F5

Отзывы:

Похожие инструкции для SANMOTION F5

Бренды по названию

Популярные бренды

Sanyo Denki SANMOTION F5, Руководство пользователя

Результаты поиска

Содержание SANMOTION F5

Отзывы:

Похожие инструкции для SANMOTION F5

Бренды по названию

Популярные бренды