SANKI S-CON MINI SLIM Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 20

background image

8

Considering frame strength, installation position of frame support is determined as follows.

Standard Installation Position of Frame Support

3

ASSEMBLY

1. Install full length of frame straight, not bent in any place.
2. Finely adjust conveyor level.

NOTE: If conveyor is bent or not level on top, belt may stray to one side or the other.

Caution When Setting up Conveyor

Standard installation interval (mm)

P1

P2

400 (150 min.)

1200 or less

«
...
6
7
8
9
10
...
»

Содержание S-CON MINI SLIM





















Отзывы:

Нет отзывов

Похожие инструкции для S-CON MINI SLIM

Бренд: CAME Страницы: 104

Бренд: Valeo Страницы: 36

Tetrix 230 AC/DC Comfort 8P TM

Бренд: EWM Страницы: 82

Бренд: RTRMAX Страницы: 14

Бренд: Patlite Страницы: 38

Бренд: Lamp Страницы: 8

Бренд: Herz Страницы: 98

Бренд: Miyachi Страницы: 59

DIX GO 1206.M C

Бренд: DINSEO Страницы: 11

Бренд: Chamberlain Страницы: 8

LiftMaster Professional RDO800 Series

Бренд: Chamberlain Страницы: 14

Бренд: Chamberlain Страницы: 12

Бренд: Chamberlain Страницы: 40

Бренд: FAAC Страницы: 4

Бренд: Nabco Страницы: 38

Бренд: Schumacher Страницы: 24

Бренд: Raider Страницы: 102

A-Class PulsaCoil

Бренд: Gledhill Response Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды