Single Bather Spa Baths
SIGNATURE AND DESIGNER “ELITE” 3-ZONE COMMAND PAD
06
1
STanDBY Mode LED Indicator
Indicates the system is ready
to operate.
2
OFF Button
Turns the jets OFF and returns the system to STANDBY.
3
LIgHT Button
Used to control the optional mood light.
• Press the “Light” button to turn on the mood light
• The light displays 7 vivid colors and 2 sequencing settings.
• To change the light color, press the “Light” button to turn it off
and after one second press it again to turn it on.
• The color sequence is as follows: Bright White, Aqua Blue,
Soothing Blue, Ocean Blue, Majestic Gold, Shamrock Green, Fiery
Red, Chameleon Mode, Party Mode
• In the event that the light is left turned on, it will automatically
turn off after 2 hours continuous operation.
4
Display
Displays the time remaining for system operation (the
timer counts down from 20 minutes and is reset when leaving the
STANDBY Mode).
5
aLL jETS Button
Simultaneously controls all jet pairs at either
High or Low speed.
6
FOOT, MID, BaCk Buttons
Use to individually control the water
flow of the jets. Each jet pair can be set at either HI or LO speed
or turned OFF. When any of these buttons are pressed for less
than one second, the system will automatically increase or
decrease the water flow of the selected jet pair.
7
jet Flow LED Indicators
Displays the water flow of the FOOT, MID,
and BACK jets.
8
PULSE Button
Pulsates the water flow and simultaneously allows
individual jet pair control via the Foot, Mid, Back buttons. This
function allows all jets, any two jet pairs or any single jet pair to
pulse, while the non-pulsing jet pairs can be set at HI or LO speed
or turned OFF.
9
Pre-Programmed Massage Modes
All three-zone models
have three pre-programmed massage modes: LINEAR, RANDOM
and AEROBIC.
LInEaR
Massage Button: Activates a massage that begins with
the back and moves down the body to the feet.
RanDOM
Massage Button: Creates water pulses in patterns of
limitless variation.
aEROBIC
Massage Button: Activates a slowly changing massage
where all jets simultaneously alternate between pulses and
constant flow.
10
Personal Memory Modes
The Personal Memory modes allow you
to store and recall the settings of the command pad via a single
button (the state of the mood light is not included). All 3-Zone
models can store and recall two personalized memory settings via
the Memory 1 and Memory 2 buttons.
MEMORY 1 Button
To store your MEMORY 1 setting, press and hold
the MEMORY 1 button until the MEMORY 1 LED Indicator turns ON to
acknowledge the setting has been stored. To recall MEMORY 1 setting,
press the MEMORY 1 button for less than 1 second.
MEMORY 2 Button
To store your MEMORY 2 setting, press and hold
the MEMORY 2 button until the MEMORY 2 LED Indicator turns ON to
acknowledge the setting has been stored. To recall the MEMORY 2
setting, press the MEMORY 2 button for less than 1 second.
9) Pre-Programmed Massage Modes:
All 6-Jet models have three pre-programmed massage
modes: LINEAR, RANDOM and AEROBIC.
LINEAR Massage Button:
Activates a massage that begins with the back and
moves down the body to the feet.
RANDOM Massage Button:
Causes the jet pairs to alternate between pulse and
constant flow.
AEROBIC Massage Button:
Activates a slowly changing massage where all jets
simultaneously alternate between pulses and
constant flow.
10) Personal Memory Modes:
The Personal Memory modes allow you to store and recall
the settings of the command pad via a single button (the
state of the mood light is not included). All 6-Jet models
can store and recall two personalized memory settings via
the Memory 1 and Memory 2 buttons.
MEMORY 1 Button:
To store your MEMORY 1 setting, press and hold the
MEMORY 1 button until the MEMORY 1 LED Indicator
turns ON to acknowledge the setting has been stored.To
recall MEMORY 1 setting, press the MEMORY 1 button
for less than 1 second.
MEMORY 2 Button:
To store your MEMORY 2 setting, press and hold
theMEMORY 2 button until the MEMORY 2 LED Indicator
turns ON to acknowledge the setting has been stored. To
recall the MEMORY 2 setting, press the MEMORY 2
button for less than 1 second.
6-JET COMMAND PAD:
COMMAND PAD FUNCTIONS:
1) STANDBY Mode LED Indicator:
Indicates the system is ready to operate.
2) OFF Button:
Turns the jets OFF and returns the system to STANDBY.
3) LIGHT Button:
Used to turn the optional mood light ON and OFF. Once
the mood light is ON, the system will automatically turn
it OFF after 2 hrs.
4) Display:
Displays the time remaining for system operation (the
timer counts down from 20 minutes and is reset when
leaving the STANDBY Mode).
5) ALL JETS Button:
Simultaneously controls all jet pairs at either HI or LO
speed.
Use to individually control the water flow of the FOOT,
MID, and BACK jets. Each jet pair can be set at either HI
or LO speed or turned OFF. When any of these buttons
are pressed for longer than 1.0 second, the system will
automatically increase or decrease the water flow of the
selected jet pair.
6) FOOT, MID, and BACK Buttons:
7
6
8
4
3
2
1
9
7) Jet Flow LED Indicators:
Displays the water flow of the FOOT, MID, and BACK
jets.
8) PULSE Button:
Pulsates the water flow and simultaneously allows
individual jet pair control via the FOOT, MID, and BACK
buttons. This function allows all jets, any two jet pairs or
any single jet pair to pulse, while the non-pulsing jet pairs
can be set at HI or LO speed or turned OFF.
5
1 0