background image

Installation & Operation Manual                                                                                   Merlin 1000S+ 

 

 

 

 

1000S+

 

IOM

 

Rev: 9    07-20

 

 

INSTALLATION 

   Planning 

 

The Merlin 1000S+ gas pressure proving and electric isolation system is designed specifically 
for use in educational establishments and laboratories.  
 
This panel is to be used to carry out a gas proving test on the pipe work in order to highlight if 
there is a gas appliance open or a gas leak in a laboratory or similar environment.  
The Merlin 1000S+ is designed to give the teacher full control over the incoming gas supply 
and bench electrics with the lockable main key-switch and touch sensors. 
 
The Merlin 1000S+ can work in conjunction with carbon dioxide, natural gas, carbon 
monoxide and LPG sensors. The Merlin 1000S+ also has a built in “timeout” facility which will 
automatically shut off the gas solenoid valve at the end of a specific time period, this time 
period can be adjusted to 2, 5, 8 hours or can be overridden if required.  
 

 

 

   Fixing - Mounting 

 

Unpack all the parts! 
 

 

1.

 

Carefully remove the front cover from the unit by unscrewing the four bolts located at each 
corner. To do this – use the socket wrench provided. 
 

2.

 

Mark the four screw holes located on the back of the enclosure to the wall. Ensure the wall 
surface is flat to prevent base distortion. 

 

3.

 

After executing the mounting and the connections – replace the front cover and insert the 
security caps over the four bolts. 

 

 

 

 

 

Please refer to your detector manual for important information regarding coverage, 

location and positioning including areas and conditions to avoid. 

 

 

Be careful when creating access for cables – Damage to boards will void any warranty. 

Carefully remove the circuit board before drilling cable entry holes.

 

Содержание Merlin 1000S+

















Отзывы: