S&C Mark VI Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 56

background image

712-502 8

INSTALLATION

Ç

CAUTION

The user-furnished mounting structure
must meet the guidelines for static and
dynamic loading limits listed in S&C
Data Bulletin 712-60.

Failure to observe

these guidelines can result in equip-
ment damage.

Before Starting

If a detailed technical drawing of the user-
furnished mounting structure was supplied
when the switch was ordered, appropriate
mounting holes will be pre-drilled in the base
of each pole-unit. Mounting brackets, channel
sections, or spacers may be supplied with the
Mark VI Circuit-Switcher to facilitate instal-
lation on the existing user-furnished structure.
Refer to the supplied custom erection drawing
for details.

If a detailed technical drawing of the user-

furnished mounting structure was not supplied
when the switch was ordered, the pole-units
will be furnished with the mounting hole pattern
appropriate for Circuit-Switchers installed on
S&C Mounting Pedestals. A standard erection
drawing and reference drawing will be sup-
plied. Refer to this standard erection drawing
for details.

Step 1

Before removing the disconnect pole-units from
the skid, arrange the skid on a level surface, in
the position and order in which they will be
raised onto the mounting structure, as shown
on the associated erection drawing.

Step 2

Unbolt the wooden cross braces that secure the
disconnect pole-units to each other.

DO NOT

unbolt the disconnect pole-units from the base
of the shipping skid at this time. See Figure 1.

Figure 1. Remove all packing materials from the disconnect pole-units.
DO NOT unbolt the disconnects from the skid until lifting slings are
attached.

Skid

Disconnect
pole-units

Skid

«
...
6
7
8
9
10
...
»

Содержание Mark VI

























































Отзывы:

Нет отзывов

Похожие инструкции для Mark VI

Бренд: janitza Страницы: 30

Бренд: Ideal Heating Страницы: 16

Бренд: Albrecht Страницы: 4

Бренд: Filabot Страницы: 8

Бренд: Chipsee Страницы: 14

Бренд: Background Images Страницы: 23

Бренд: Baelz Automatic Страницы: 36

Бренд: Kampmann Страницы: 48

Бренд: Pack Leader Страницы: 131

Бренд: Avtech Страницы: 6

Conductix-Wampfler 040874-014x2,0

Бренд: Delachaux Страницы: 29

KF2 1500 - 7500

Бренд: Kaller Страницы: 4

Бренд: FLENDER Страницы: 80

Бренд: Angelus Страницы: 81

HD67801-KNX-BIP-B2

Бренд: ADF Web Страницы: 31

Бренд: Orenco Страницы: 2

Loc Check A5900/ Series

Бренд: Hasco Страницы: 8

Бренд: LI-COR Страницы: 846

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды