S&C Mark VI Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 56

background image

712-502 26

INSTALLATION

Wiring the Interrupters and
Charging Motors

Repeat Steps 39 through 45 for each interrupter
and charging motor.

Ç

CAUTION

DO NOT

remove the window bolts on the

interrupter. The interrupter is pressurized to
75 PSIG.

Serious injury could occur.

Step 39

Remove the outer motor bracket. Retain the
hardware. Remove the three removable screws
of the interrupter electrical junction box
cover. Retain the hardware. Loosen the fourth
retaining screw. Swing out the cover to access
the wiring inside the electrical junction box. See
Figures 36 through 38.

Step 40

Following the wiring diagram furnished,
connect the conduit wiring to the wiring inside
the electrical junction box. Use the butt splices
supplied with the junction-box wiring. The butt
splices accommodate 18 to 22 AWG wire.

NOTICE

To ensure proper crimping of the butt
splices, use a Panduit controlled-cycle hand
tool (CT-1550) or a similar tool for attaching
18- to 20-gauge insulated ring lugs.

Step 41

Rotate the cover of the electrical junction box
and replace the retained screws. See Figure 37.
Securely tighten all screws. Reinstall the motor
bracket removed in Step 39. Torque the removed
5/8-inch stud nuts to between 70 and 80 ft.-lbs.
See Figure 36.

NOTICE

When inserting the connected wires in the
electrical junction box, ensure that no wires
are pinched underneath the junction box
cover. Trim excessive wire length from the
interrupter’s electrical junction box wiring
before installation, if necessary.

Figure 36. Temporarily remove motor bracket.

Interrupter

Outer motor bracket

Electrical junction box

Figure 37. Remove the three removable screws from the interrupter electri-
cal junction box cover. Loosen but do not remove the fourth screw.

Removable screws

Retaining screw

Retaining screw

Interrupter base

Cover

Figure 38. Swing out the cover to access the wiring inside the electrical
junction box.

Electrical
junction box

Conduit
entrance

Interrupter
base

Cover

«
...
24
25
26
27
28
...
»

Содержание Mark VI

























































Отзывы:

Нет отзывов

Похожие инструкции для Mark VI

AQUIS ULTRAFLOW

Бренд: Waterous Страницы: 56

Бренд: Igema Страницы: 22

Бренд: ABB Страницы: 154

MERLIN N Series

Бренд: Meheen Страницы: 24

Бренд: R.V.R. Elettronica Страницы: 26

Бренд: Jäger Страницы: 36

Бренд: California Air Tools Страницы: 7

eBOX671-521-FL Series

Бренд: AXIOMTEK Страницы: 2

Бренд: Wood-mizer Страницы: 118

CRB AUTOMAT Touch Screen

Бренд: IBAIONDO Страницы: 28

Бренд: R.V.R. Elettronica Страницы: 218

Бренд: Ulvac Страницы: 29

Бренд: Ulvac Страницы: 55

Бренд: Viessmann Страницы: 4

Бренд: V.ORLANDI Страницы: 128

Бренд: Moeller Страницы: 2

790.4844 series

Бренд: Kenmore Страницы: 70

CyberView RP-F719

Бренд: Austin Hughes Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды