S&C Mark VI Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 56

background image

712-502 30

NOTICE

DO NOT

connect the wiring from the

interrupters or interrupter charging motors
at this time. Complete the installation
and testing of the control circuit wiring
before wiring the interrupters and charging
motors. The charging motors take approxi-
mately two minutes to close and charge the
interrupters and can cause unnecessary
delays in installation.

Step 48

Connect the external control-circuit wiring
(including space-heater source leads) to the
terminal blocks of the switch operator in
accordance with the wiring diagram furnished.
See Figure 45.

Ç

CAUTION

Unauthorized changes should not be made
in the wiring of this switch operator. Should
a control-circuit revision appear desirable,
it should be made

only

on the authority of

a revised wiring diagram, which has been
approved by

both

the user and S&C Electric

Company.

NOTICE

To ensure proper crimping of the butt
splices, use a Panduit controlled-cycle hand
tool (CT-1550) or a similar tool for attaching
18- to 20-gauge insulated ring lugs.

Step 49

Before proceeding further, familiarize yourself
with the operation of the manual operating
handle, and the selector handle. Refer to
Step 50.

WIRING AND ADJUSTING THE SWITCH OPERATOR

Figure 45. Connect external control-circuit wiring.

Terminal blocks

Terminal blocks

«
...
28
29
30
31
32
...
»

Содержание Mark VI

























































Отзывы:

Нет отзывов

Похожие инструкции для Mark VI

Бренд: VARISCO Страницы: 24

Бренд: Kobelt Страницы: 20

Бренд: Jäger Страницы: 36

Бренд: Valor Страницы: 65

Бренд: Jäger Страницы: 36

Бренд: Jäger Страницы: 36

Бренд: displayit Страницы: 6

Бренд: OBO Bettermann Страницы: 60

MB 300 el-office

Бренд: Opus Страницы: 19

Бренд: Enerpac Страницы: 32

IPPCxxB9-RE Series

Бренд: IBASE Technology Страницы: 77

Бренд: R.V.R. Elettronica Страницы: 38

Бренд: National Instruments Страницы: 105

HEX150PB Series

Бренд: Delta Страницы: 12

Бренд: Moxa Technologies Страницы: 2

Бренд: Rohm Страницы: 15

Бренд: Ekso Bionics Страницы: 29

PHANTOM DE PHB4020

Бренд: Hydrofarm Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды