S&C Mark VI Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 56

background image

712-502

11

INSTALLATION

Step 7

With the interrupter lifted off the ground, check
that the gas-pressure gauge on the underside of
the interrupter is in the “OK” to operate zone.
See Figures 7 and 8.

NOTICE

The gas-pressure gauge needle should
be in the “OK” to operate zone.

If the

gauge is not in this position, stop the
installation and notify S&C Electric
Company.

Figure 7. With the interrupter lifted off the ground, check the gas-pressure
gauge on the underside of each interrupter.

Interrupter indicators

Figure 8. Check that the gas-pressure gauge on each interrupter is in the
“OK” to operate zone.

“OK” to operate

«
...
9
10
11
12
13
...
»

Содержание Mark VI

























































Отзывы:

Нет отзывов

Похожие инструкции для Mark VI

Бренд: xsto Страницы: 76

Бренд: ubicquia Страницы: 36

Бренд: Rohm Страницы: 17

Бренд: Festo Страницы: 94

Бренд: A.B.S. Страницы: 30

Бренд: Aaeon Страницы: 97

Бренд: Nuvair Страницы: 40

Бренд: Spartan Equipment Страницы: 21

Nuvo-2400 Series

Бренд: Neousys Technology Страницы: 81

Бренд: Spirax Sarco Страницы: 52

ELCOROCK FILLING FRAME

Бренд: GEOFABRICS Страницы: 7

Бренд: Bornack Страницы: 32

Бренд: OBO Bettermann Страницы: 3

KTR-STOP TB Thuster

Бренд: KTR-Group Страницы: 17

STANDPIPE-PAC SSS-101

Бренд: UNITED Fire Systems Страницы: 67

Бренд: WABROTECH Страницы: 20

Бренд: EA Страницы: 16

M2M CONTROL CX320

Бренд: Infranet Technologies Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды