background image

TY-JS-220308-004

6

Before commissioning

a) Make sure that the water supply pipe of equipment is not
blocked;
b) It is necessary to check the water pipe and the water pump
to confirm that there is a proper amount of water entering the
water pump and exhaust it through the water pump exhaust
valve, otherwise it will cause damage to the water pump;
c) Confirm that the state of the equipment is normal and safe.
Otherwise, there may be injury and damage.

Gently move the motor

impeller if the

equipment isn’t used

for a long time

For equipment that has not been used for a long time, it may
be difficult to start the pump at the first start. Please gently
move the motor impeller before the equipment is powered on.

The equipment is

forbidden to be

trampled on

Please do not step on or sit on the equipment. Otherwise, it
may cause injury accidents such as falling or overturning

Clean the air filter

regularly

Clean the air filter at least once a week. If it is blocked, the
cooling ability will decrease and the power consumption will
increase, and the alarm will not work properly.

Equipment surface

cleaning

a) Please use cleaning agents that are non-corrosive to metals
and plastics;
b) Please keep the cleaning agent properly after cleaning to
prevent liquid leakage;
c) The container for storing the cleaning agent must be sealed
completely.

No air blowing at the

water outlet

A temp sensor is installed inside the water outlet, and it is
forbidden to blow air inside the device with an air gun.

Wear protective gloves

during maintenance,

inspection and cleaning

a) The sharp edges of the condenser fins may cut the skin;
b) The temperature of the internal compressor and refrigerant
piping is very high, and direct skin contact may cause burns.

Anti-freezing

a) When the ambient temperature is lower than 2

and the

machine is shut down for a long time, it is necessary to drain
the liquid and blow the water in the system away with
compressed air, otherwise there is a danger of freezing and
cracking the components and pipelines.
b) When room temperature is lower than 2

℃,

it is

recommended to use antifreeze with a concentration of not
more than 30% containing ethylene glycol or propylene glycol.

Содержание CW-5000 Series


















Отзывы: