Samsung SpintPoint M8-DVR Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 83

background image

Spinpoint M8-DVR OEM Product Manual REV 1.0

16

INSTALLATION

4.3.2 Ventilation

The  Spinpoint M8  hard  disk  drive  is  designed  to  operate  without  the  need  of  a  cooling  fan  provided  the
ambient air  temperature  does  not  exceed  60ºC.  Any  user-designed  cabinet  must  provide  adequate  air
circulation  to prevent exceeding the maximum temperature.

4.4

Cable Connectors

The Interface/Power connector consists of two cables; a SATA 15-pin DC power connector, and the
standard SATA 7-pin Interface connector.

4.4.1 SATA Connectivity

The  SATA  interface  is  connected  within  a point  to point  configuration  with  the  SATA  host  port.  There  is
no master  or  slave  relationship  within  the devices.  Thus  SATA  does not  require  master/slave  jumper.  The
drive interface  section  of  the  host  adapter  employs  a  new  design  which  processed  data  into  a  serial  data-
control system.

Figure 4.4 illustrates the connection for the SATA.
There  are  two  cables  for  SATA  drives.  One  is  for  data  transmission.  The  other  is  for  power.  Figure  4-4
illustrates (a) device signal plug connector, (b) device  power  plug  connector,  (c)  signal  cable  receptacle
connector  mating  with  (a),  and  (d)  power  cable  receptacle  connector  to  be  mated  with  (b).  For  more
information, please refer to SATA Specifications cited in the reference.

.

Figure 4-4 Serial ATA Connector

«
...
20
21
22
23
24
...
»

Содержание SpintPoint M8-DVR




















































































Отзывы:

Нет отзывов

Похожие инструкции для SpintPoint M8-DVR

Бренд: SAJ Страницы: 28

Бренд: Seagate Страницы: 57

Бренд: G-Technology Страницы: 17

Бренд: IBM Страницы: 2

Бренд: IBM Страницы: 258

MY PASSPORT EDGE

Бренд: Western Digital Страницы: 77

Бренд: DuraMax Страницы: 81

GridLine 930505

Бренд: GARANT Страницы: 116

Бренд: CalDigit Страницы: 16

storagetek sl150

Бренд: Oracle Страницы: 196

Бренд: Addonics Technologies Страницы: 8

Бренд: Yardmaster Страницы: 24

Бренд: Infrant Technologies Страницы: 2

Бренд: Infrant Technologies Страницы: 8

WD10000E035 - Elements Desktop

Бренд: Western Digital Страницы: 2

Бренд: SmartStore Страницы: 16

Desktop Hard Drive USB 2.0

Бренд: Verbatim Страницы: 116

Бренд: Sanborn Mfg Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды