manualshive.com logo in svg

Samsung SpintPoint M8-DVR, Руководство по эксплуатации продукта

Samsung SpintPoint M8-DVR - продукт для хранения данных с высокой емкостью для DVR систем. На нашем сайте вы можете бесплатно скачать руководство пользователя для этого устройства. Получите полезные советы и инструкции по использованию Samsung SpintPoint M8-DVR прямо сейчас на manualshive.com.

Поделиться
Скачать
background image

Spinpoint M8-DVR OEM Product Manual REV 1.0

 

71 

 

 

 

 

   

device  shall  suspend  off-line  data  collection  activity  after  an  interrupting  command  and  resume  off-line 
data collection activity after some vendor-specified  event. 

 

 

 

Bit 3 (off-line read scanning implemented bit) - If this bit is cleared to zero, the device does not support 

off-line read scanning. If this bit is set to one, the device supports off-line read scanning 

 

 

 

Bit 4 (self-test implemented bit) – If this bit is cleared to zero, the device does not implement the Short 

and  Extended  self-test  routines.  If  this  bit  is  set  to one,  the  device  implements  the  Short  and Extended 
self-test routines. 

 

 

 

Bit 7-5 (reserved). 

 
SMART capability 

 

 

The  following  describes  the definition  for the  SMART  capability  bits.  If the value of all of these  bits is  equal 
to zero, then this device does not implement automatic saving of SMART data. 

 

 

 

 

Bit  0  (power  mode  SMART  data  saving  capability  bit)  –  If  the  value  of  this  bit  equals  one,  the  device 

shall  save  its  SMART  data  prior  to  going  into  a  power  saving  mode  (Idle,  Standby,  or  Sleep)  or 
immediately  upon  return  to  Active  or  Idle  mode  from  a  Standby  mode.  If  the  value  of  this  bit  equals  zero, 
the  device  shall  not  save  its  SMART  date  prior  to  going  into  a  power  saving  mode  (Idle,  Standby,  or 
Sleep) or immediately upon return to Active or Idle mode from a Standby mode. 

 

 

 

Bit  1  (SMART  data  auto-save  after  event  capability  bit)  –  The  value  of  this bit  shall  be  equal  to  one  for 

devices complying with this standard. 

 

 

 

Bits 2-15 (reserved). 

 

Self-test routine recommended polling time 

 

The  self-test  routine  recommended  polling  time  shall  be  equal  to  the  number  of  minutes  that  is  the  minimum 
recommended  time before which  the host should first poll for test completion status. Actual test time could be 
several  times  this  value.  Polling  before  this  time  could  extend  the  self-test  execution  time  or abort  the  test 
depending on the state of bit 2 of the off-line data capability bits. 

 

The  data  structure  checksum  is  the  two’s  compliment  of  the  result  of a  simple  eight-bit  addition  of  the  first  511 
bytes in the data structure. 

 
8.2.34.6         SMART read log sector (D5h)

 

 

This command returns the indicated log sectors to the host. 

 

8.2.34.7         SMART return status (DAh)

 

 

This command  is used to communicate  the reliability  status  of the device to the host at the host’s request.  If a 
threshold exceeded condition is not detected by the device, the device shall set the Cylinder Low register to 
4Fh  and  the Cylinder  High  register  to C2h. If  the device  detects  a threshold-exceeded  condition,  the device 
shall set Cylinder Low register to F4h and Cylinder High register to 2Ch 

 

 

8.2.34.8         SMART write log sector (D6h)

 

 

 

This command writes number of 512-byte data sectors to the indicated log sector. 
 

Содержание SpintPoint M8-DVR




















































































Отзывы:

Нет отзывов

Похожие инструкции для SpintPoint M8-DVR

Eastwood 31554 Instructions Manual preview
31554
Бренд: Eastwood Страницы: 8
LaCie LaCie Ethernet Big Disk Quick Install Manual preview
LaCie Ethernet Big Disk
Бренд: LaCie Страницы: 16
LaCie 4BIG QUADRA USB 3.0 User Manual preview
4BIG QUADRA USB 3.0
Бренд: LaCie Страницы: 41
LaCie 5big - Network NAS Server Quick Start Manual preview
5big - Network NAS Server
Бренд: LaCie Страницы: 9
LaCie 2big NAS Quick Install Manual preview
2big NAS
Бренд: LaCie Страницы: 14
LaCie Hard Drive Quick Install Manual preview
Hard Drive
Бренд: LaCie Страницы: 13
LaCie D2 BLU-RAY XL Manual preview
D2 BLU-RAY XL
Бренд: LaCie Страницы: 29
LaCie D2 BLU-RAY XL Brochure & Specs preview
D2 BLU-RAY XL
Бренд: LaCie Страницы: 4
Quantum Scalar 50 Quick Start Manual preview
Scalar 50
Бренд: Quantum Страницы: 42
Quantum Scalar i500 Getting Started Manual preview
Scalar i500
Бренд: Quantum Страницы: 148
QNAP TVS-73e Series Quick Installation Manual preview
TVS-73e Series
Бренд: QNAP Страницы: 24
G-Technology G-SPEED FC Product Manual preview
G-SPEED FC
Бренд: G-Technology Страницы: 17
Spectra Logic Spectra 2K Library User Manual preview
Spectra 2K Library
Бренд: Spectra Logic Страницы: 93
SanDisk 175972 User Manual preview
175972
Бренд: SanDisk Страницы: 2
Hama Tenus FlashPen Operating Instruction preview
Tenus FlashPen
Бренд: Hama Страницы: 4
Accordance Systems ARAID M500 User Manual preview
ARAID M500
Бренд: Accordance Systems Страницы: 22
WiebeTech Forensic ComboDock FCDv6 Manual preview
Forensic ComboDock FCDv6
Бренд: WiebeTech Страницы: 20
GARANT GridLine 930505 Instruction Manual preview
GridLine 930505
Бренд: GARANT Страницы: 116

Бренды по названию

Популярные бренды

Загрузить еще бренды