Samsung SpintPoint M8-DVR Скачать руководство пользователя страница 14

Страница: 14 / 83

Spinpoint M8-DVR OEM Product Manual REV 1.0

SPECIFICATIONS

3.4

Performance Specifications

Table 3-4: Performance Specifications

NOTES:

 Seek time is defined as the time from the receipt of a read, write or seek command until the actuator has

repositioned and settled on the desired track with the drive operating at nominal DC input voltages and
nominal operating temperature.



Average seek time is determined by averaging the time to complete 1,000 seeks of random length.



Average latency is the time required for the drive to rotate 1/2 of a revolution and on average is incurred
after a seek completion prior to reading or writing user data.



Startup time is the time elapsed between the supply voltages reaching operating range and the drive being
ready to accept all commands.



Actual rotational speed can be different a little.

Performance specification is limited to the room temperature & normal voltage condition.

DESCRIPTION

ST320LM001

ST500LM012

ST750LM022

ST1000LM024

Seek Time (RD/WRT, Typ)

Average seek time

Track to track seek time

Full stroke seek time

12/14 ms

2/4 ms

22/24 ms

Average Latency

5.6 ms

Data Transfer Rate (Max)

buffer to/from media

host to/from buffer

145Mbits/s

600 MB/s

Rotational Speed

5400 RPM Class

Startup Time

(Typ)

Power on to Drive Ready

Standby to Drive Ready

3.0 sec
2.5 sec

Содержание SpintPoint M8-DVR




















































































Результаты поиска

Содержание SpintPoint M8-DVR

Отзывы:

Похожие инструкции для SpintPoint M8-DVR

Бренды по названию

Популярные бренды

Samsung SpintPoint M8-DVR, Руководство по эксплуатации продукта

Результаты поиска

Содержание SpintPoint M8-DVR

Отзывы:

Похожие инструкции для SpintPoint M8-DVR

Бренды по названию

Популярные бренды