Samsung SF-150T Скачать руководство пользователя | Manualshive

Страница: 48 / 67

background image

Operating Instructions

SF150T

3-3

LINE MONITOR

Allows you to monitor line signals through the
speaker.

RX LEVEL

Reception level may be too low due to cable losses.
If set to - 43 dBm, reception sensitivity will be
between 0 and - 43 dBm.
If set to - 48 dBm, reception sensitivity will be
between -5 and -48 dBm.

BUSY TONE DETECTION LEVEL

While checking tone in ANS/FAX mode, If any
signal which is great than set level is detected for a
few seconds the machine will disconnect the line.

BUSY ON DROP OUT TIME

While checking busy on time, if any signal noise is
detected, the machine will ignore the signal noise
unless it is greater than a specified time.

BUSY OFF DROP OUT TIME

While checking busy off time, if any signal noise is
detected, the machine will ignore the signal noise
unless it is greater than a specified time.

PAUSE TIME

Adjust the period of pause time to wait for a
second dial tone in a PABX or mobile paging
system. You can adjust the time from 0 sec to 9 sec
(0 to 9).

RECALL TIME

When a call comes in and you want to connect it to
another party, you can transfer the call by using a
timed-break recall funtion.
This funtion must make a properly timed break
authorized by the country. The machine can select
times of 100, 280, or 600 msat an accuracy of ± 10
ms of the setting.

MH/MR CODING

Selection the coding method used for picture
detail
MR = Use MR and MH coding.
MH = Use only MH coding.

RING ON CHECK TIME

The machine must receive a ring signal with a
specified active time from a telephone exchange in
automatic reception mode. The detection time that
the machine considers valid is adjustable via this
option. If the active time of the ring signal is less
than the set value of the Ring On Check Time, the
machine will not consider it a ring signal.

RING OFF CHECK TIME

The machine must receive a ring signal with a
specified inactive time, as well as an active time. If
the inactive time of the ring signal is longer than
the value of the Ring Off Check Time, the machine
will not consider it a valid ring signal.

3-2-2 Changing Options

Press Ô

MENU

, 3,

Start

/COPYÕ in sequence. Press

^ or v to select the desired option item.
When the desired item appears, press

Start

and

use ^ or v to change the status of the selected
option.

«
...
46
47
48
49
50
...
»

Содержание SF-150T




































































Отзывы:

Нет отзывов

Похожие инструкции для SF-150T

Бренд: UNIS Страницы: 19

Бренд: Bulldog Security Страницы: 7

Бренд: Reliable Страницы: 44

Бренд: Viper Страницы: 2

Бренд: Truvox Страницы: 12

Бренд: Antari Страницы: 12

CoverPro 1000CP

Бренд: Janome Страницы: 21

SEWHANDY MODEL 40K

Бренд: Singer Страницы: 12

Бренд: Singer Страницы: 25

Бренд: MasterCraft Страницы: 8

Бренд: ELNA Страницы: 61

Бренд: Singer Страницы: 56

Бренд: Nilfisk-Advance Страницы: 39

Бренд: JUKI Страницы: 380

Бренд: JUKI Страницы: 32

Бренд: Janome Страницы: 92

Бренд: Samsung Страницы: 92

Бренд: Chikon Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды