Samsung SF-150T Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 67

background image

Circuit Description

SF150T

5-9

Serial interface

¥ U201 pin 11 RXD: Schmitt trigger input

(threshold = 2.5V) to serial interface.

¥ U201 pin 29 TXD: Open drain output from serial

interface.

¥ The communication is standard UART :

Baud Rate 9600
Start Bit 1
Stop Bit 1
Data Bits 8

Parity Bit None
LSB is transferred prior to MSB.

5-6-2 Telephone Section

RINGER CIRCUIT

¥ When a ringing signal is applied to the line, Vdd

of U201 (I-LIU) is charged via an external path.
After Vdd has reached the operating voltage the
oscillator starts and U201 detects the ring
frequency.
After a valid ring frequency is applied to the
U201 pin 25 RFD (Ring Frequency
Discrimination) port, the ring melody generator
of U201 sends out a 3-tone melody via U201 pin
28 MO (Ring Melody Output) port.

¥ U201: I-LIU and associated components.
¥ Ring frequency passes through DC blocking

capacitor C206 (C205 for Switzerland or Austria)
and Zener-diode ZD205 (ZD209 for Switzerland
or Austria) to U201 pin 25 RFD port.

¥ Line ring voltage passes through DC blocking

capacitor C201, current limit resistor R205,
bridge diode BD201, CML relay, and Hook
Switch to FET201 (BS170) pin 3, C214, ZD203
and R246.

¥ The ring frequency discriminator of U201

assures that only signals with a frequency
between 13Hz and 70Hz are regarded as valid
ring signals.

¥ When a valid ring signal is present for at least

73ms, the ring melody generator (pin 28, MO) is
activated and remains active as long as a valid
ring signal is present.

¥ U201 filters the ring signals and output is pin 28

(MO).

¥ The 3 basic melody frequencies are : F1 = 880 Hz,

F2 = 1067 Hz, and F3 = 1333 Hz. The repetition
rate is set to 4 which means that the sequence of
F!, F2, F3, F1, F2, F3 is repeated 4 times within a
second.

Speech Circuit

¥ U201 (STI9510) and associated components.
¥ Handset transmitting circuit: Handset

transmitter audio (Condensor MIC.) is filtered
by R240, C232, C224, C225, C226, C227, C229 and
C230, and then amplified by U201 pin 32 and 33
(M1, M2).

¥ Handset receiving circuit: Handset receiver

(Dynamic unit) is filtered by R229, C241, C209,
C203 and C231, and then applied to U201 pin 1
(ROH) and VSS.

¥ U201 pin 39 (LS) is audio output to telephone

line.

Sidetone Circuit

¥ Sidetone audio characteristics are controlled by
R238, R235, R237, R239, and C202 connected to
U201 pin 7 STB.

«
...
38
39
40
41
42
...
»

Содержание SF-150T




































































Отзывы:

Нет отзывов

Похожие инструкции для SF-150T

Бренд: Janome Страницы: 59

Бренд: Janome Страницы: 42

Бренд: Panasonic Страницы: 256

KXFG2451 - B/W Thermal Transfer

Бренд: Panasonic Страницы: 20

UF 8200 - Panafax - Multifunction

Бренд: Panasonic Страницы: 6

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 150

Бренд: Panasonic Страницы: 112

Бренд: Panasonic Страницы: 12

KX-FL521 - B/W Laser - Fax

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 50

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 84

Бренд: Panasonic Страницы: 104

Бренд: Panasonic Страницы: 24

Бренд: HappyJapan Страницы: 216

Бренд: Janome Страницы: 43

Бренд: TAJIMA Страницы: 140

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды