Samsung SF-150T Скачать руководство пользователя страница 45

Страница: 45 / 67

Disassembly Instruction

4-4

SF150T

4-8. BOARDS & POWER SUPPLY

LIU PBA

MAIN PBA

BASE

POWER

¥ Remove the handset modular harness from the

LIU board.

¥ Loosen the screw fastening the LIU board and

carefully lift the LIU board as shown by the
arrow.

¥ Loosen the 3 screws connecting the main and

daughter boards. Lift the rear bracket.

¥ Loosen the screw fastening the daughter board

to the base. Lift the daughter board.

¥ Loosen the 2 screws fastening the power supply

to the base. Lift the power supply and the main
board to remove them.

¥ Lift the modular jack and the earth spring.

¥ Lift the white roller assembly.

¥ Loosen the 2 E-rings fastening the main chassis

assembly.

¥ Remove the spring-lock.

¥ Loosen the 3 screws fastening the main chassis

assembly.

¥ Lift the CIS assembly.

¥ Remove the document guide from the CIS

assembly (2 screws).

¥ Remove the CIS guide from the CIS (2 screws).

4-7. CIS

Figure 4-7

Содержание SF-150T




































































Результаты поиска

Содержание SF-150T

Отзывы:

Похожие инструкции для SF-150T

Бренды по названию

Популярные бренды

Samsung SF-150T, Руководство по обслуживанию

Результаты поиска

Содержание SF-150T

Отзывы:

Похожие инструкции для SF-150T

Бренды по названию

Популярные бренды