Samsung SF-150T Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 67

background image

SF150T

3-1

3. Operating Instructions

3-1 Service Mode

In Service Mode, the technician can check the machine and perform various tests to isolate a machine
malfunction.

To enter Service Mode, press Ô

MENU

, #, 1, 9, 3, 4Õ in sequence, and '

' will be displayed in the LCD to

confirm that the machine has entered Service Mode. While in Service Mode, the machine still performs all
normal operations. To return to normal User Mode, press '

MENU

, #, 1, 9, 3, 4' in sequence again, or turn

the power off, then on by unplugging and replugging the power cord.

3-2 Changing Options

3-2-1 Selectable Options

CONFIRMATION REPORT

Select whether a confirmation report prints each
time a user sends a fax.

YES: The machine prints a report automatically

after each fax sent.

ERROR : The machine prints a report only when

there is an error.

NO: The machine does not print a report

automatically. User can print the list on
demand.

DIAL TYPE

Select the type of dial system to which the machine
is connected.

Select MF if connected to a tone dial system.
Select DP if connected to a pulse dial system.
Use ^ or v buttons to select, then press Start.

RING COUNT

Select the number of rings the machine allows
before it answers a call in automatic receiving
mode.

CALLER ID

This is the number of the person faxing you.

Choose YES to turn on Caller ID display.
Choose NO to disable.

REMOTE RECEIVE CODE

This code can be used only with a phone extension
connected to the FAX machine. The user can
initiate FAX receive mode by entering a remote
receiving code on the extension phone. The code is
factory preset to 9 , and the middle character
may be changed to any digit between 0 and 9.

AUTO PRINT

The machine prints a TX/RX journal automatically
after every 20 fax sessions.

MODEM SPEED

Select baud rate of 9600, or 4800 bps. The lower the
baud rate, the larger the acceptable error rate. T30
protocol has a fixed speed of 300 bps in the
protocol mode. When the TX speed is set to 9600
bps, the RX speed will be V.29. When the TX
speed is set to 4800 bps, the RX speed will be V.27
ter.

T

«
...
44
45
46
47
48
...
»

Содержание SF-150T




































































Отзывы:

Нет отзывов

Похожие инструкции для SF-150T

Бренд: Janome Страницы: 48

Бренд: Janome Страницы: 102

Бренд: Janome Страницы: 6

Бренд: Janome Страницы: 40

Horizon Memory craft 7700 QCP

Бренд: Janome Страницы: 5

Horizon MC8900 QCP Special Edition

Бренд: Janome Страницы: 112

Бренд: Janome Страницы: 4

Бренд: Janome Страницы: 17

Continental M7 Professional

Бренд: Janome Страницы: 51

Бренд: Janome Страницы: 88

Бренд: Janome Страницы: 32

Бренд: Janome Страницы: 2

Бренд: Janome Страницы: 7

Бренд: Janome Страницы: 79

Бренд: Janome Страницы: 41

Бренд: Janome Страницы: 38

Memory Craft 3500

Бренд: Janome Страницы: 2

KM 130/300 R Bp

Бренд: Kärcher Страницы: 372

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды