Samsung SF-150T Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 67

background image

Circuit Description

SF150T

5-7

5-5-1 DSP

This circuit consists of host interface, memory
interface, CODEC interface.
receives data to the compressed voice data to and
from KS16118.
Memory interface sends and receives data to the
compressed voice data to and from DRAM to play
back and record voice data.
DSP communicates with host KS16118 through host
interface.

5-5-2 Recording Path

The voltage is supplied with MIC as using the
MX93000AFC's Vref Voltage (2.25V), and the voltage
entering into MIC is trasmitted to electric signal and
enters into MX93000AFC's MIC terminal.
Input signal is amplified by MX93000AFC's ALC
until maximum 26dB (Max. 3V

P

-

P

) according to

signal size.
The signal enters into PCM CODEC that converts to
D/A and compresses in the DSP Chip and stores in
DRAM.

5-5-3 Play Path

The signal stored in DRAM is decomressed in DSP
and enters into MX93000AFC.
Input signal is converted to D/A again and is
amplified by LIU-DRV amplifier and comes into
LOUT terminal through or comes into terminal
after being attanuated by ATT (Electronic Volume)
or SPK-DRV.

5-5-4 Voice Backup

+5V is supplied for DSP or voice memory through
VBT when power is on.
When power is off, +5V is supplied from the 9V
backup battery.

When supply voltage is "ON", U9(5V Voltage
Regulator) makes 5V Supply Voltage.
The signal is supplied with DSP or DRAM and it
caused that the data is protected.
When supply voltage is "OFF", U9 makes 5V Voltage
as using the 9V Battery.
And then the voltage is used to "backup supply
voltage" in DSP or DRAM.
If the supply voltage were "OFF" as using the full
charged 9V Battery, voice data is usually protected
for twenty hours.

5-5 TAD

TAD circuit consists of a voice coprocessor to record and play voice messages and voice memory.

1) TX CIRCUIT
The output signal coming from internal modem
KS16118 enters MX93000AFC through AUX2
terminal after amplfied by OP AMP U1.
That signal passes through internal switch, is
amplified by LIN-DRV amplfier and is sent to LIU
board through LOUT terminal.

2) RX CIRCUIT
The signal goming into LIU terminal through LIU
board is amplified by MX93000AFC's PRE-PGA,
passes through internal switch and goes into FILT
terminal.
After the singal is diminished by OP AMP U1, it
enters internal modem of KS16118.

«
...
36
37
38
39
40
...
»

Содержание SF-150T




































































Отзывы:

Нет отзывов

Похожие инструкции для SF-150T

Бренд: Baby Lock Страницы: 364

Perfect Binder G10 120

Бренд: Riso Страницы: 78

Бренд: Janome Страницы: 61

Truvox International Orbis Compact

Бренд: Tacony Страницы: 14

Бренд: GBC Страницы: 2

NC81200 CLASSES

Бренд: Carpet Sergers Страницы: 30

Бренд: Hefter Страницы: 71

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 60

Бренд: Panasonic Страницы: 76

Бренд: Panasonic Страницы: 48

Бренд: Panasonic Страницы: 48

Бренд: Panasonic Страницы: 100

Бренд: Panasonic Страницы: 52

Бренд: Panasonic Страницы: 114

Бренд: Panasonic Страницы: 114

Бренд: Panasonic Страницы: 80

Бренд: Panasonic Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды