5-1
Chapter 5 Power Up Procedures
Before powering up your system, ensure that all of the procedures described in the previous
chapters have been followed carefully.
Connect Power to the System
During the initial installation, it is best to verify proper system operation before plugging in any
amphenol-type cables to the MDF. If you have already plugged the cables in, unplug them.
1. Verify that the AC voltage at the dedicated AC outlet is in the range 88~132 VAC or 210~230
VAC.
Verify that the AC voltage selection switch on the PSU is set for the correct volt-
age 110 or 220 VAC.
2. Verify that a supplemental ground has been connected.
3.
Make sure the AC power switch (PWR) on each cabinet is in the OFF position
which shows the position of the PWR switch). Plug one end of each
power cord into the power input connectors on the main cabinet and expansion cabinets (see
). Plug the other end of each cable into the dedicated AC outlet or
power strip. Confirm that all expansion cabinets are connected to the main cabinet with ap-
propriate cables.
4. Turn the AC power switch (PWR) to the ON position on each of the expansion cabinets.
5. Turn the AC power switch (PWR) to the ON position on the main cabinet.
Processor Card LED Indications
After verifying correct operation of the power supply, visually check the processor card LED
indications. If operating correctly, the LEDs should display as follows:
CARD
LED
STATUS
MCP
Flickers rapidly, indicating the main processor is functioning
MCP2
SM
On steady, indicating that the SmartMedia card is present and
recognised
HDLC (TX, RX)
Flickering
SCP2
SCP
On steady
HDLC (TX, RX)
Flickering
LCP2
LCP
On steady
¹
If the SM LED on the MCP card does not light or flash
, the system does not recognize
the SmartMedia card. Power down the main cabinet, replace the SmartMedia card and re-
peat the power up procedure. If the problem is not corrected, power down and remove the
MCP2 card. Check the card to ensure it is configured correctly.
Содержание OfficeServ500
