Samsung DVM Series Скачать руководство пользователя страница 246

Страница: 246 / 390

- 245 -

Troubleshooting

8-2-77. Indoor unit EEV OPEN error

Indoor unit display

Outdoor unit display

Judgment method

Causes

detection : (Displayed only outdoor unit)

detection : x x x (x x x : Indoor unit address occurred error)

(Operation)

(Timer)

(Fan)

(Filter)

(Removing frost)

- Refer to the below judge method

- Indoor unit EEV operation defect (The refrigerant leaks to the stopped indoor unit.)

1. Judge Method

1) Detected only in cooling mode.(Not detected in heating mode.)

2) The temperature of inlet or outlet of stop indoor heat exchanger maintains for more than 20 minutes below 0˚C

in cooling mode.

2. Check method

1) Check whether the EEV wire is connected correctly to the indoor unit PCB.

2) Check whether the EEV coil is inserted to the main body correctly.

3) After pressing the reset key(K3) of outdoor unit, check if the same error is occurred.

●

If it is the CLOSE error, operate the corresponding indoor unit.

●

If it is OPEN error, turn the power of corresponding indoor unit off to check.

4) If there is no trouble for the above checks, replace the EEV of the corresponding indoor unit.

●

Since the replacement of EEV is the inconvenient work to collect the all refrigerant in the system, be sure to check the

above items before replacing EEV.

DB98-17816A(1)_8 3/2/04 9:35 AM Page 245

Содержание DVM Series







































































































































































































































































































































































































Результаты поиска

Содержание DVM Series

Отзывы:

Похожие инструкции для DVM Series

Бренды по названию

Популярные бренды

Samsung DVM Series, Руководство по обслуживанию

Результаты поиска

Содержание DVM Series

Отзывы:

Похожие инструкции для DVM Series

Бренды по названию

Популярные бренды