Samsung DVM Series Скачать руководство пользователя страница 195

Страница: 195 / 390

- 194 -

Troubleshooting

1. Judgment method

Compressor is on in cooling operation & inlet/outlet temperature of stopped indoor unit is

below 0°C for 2.5 minutes.

2. Judgment time

Starts detecting after 5 minutes from completion of the safety start.

3. Control

4. Check method

1) Check whether the electronic expansion valve wire is connected correctly to the indoor unit PCB.

2) Open the electronic expansion valve kit to check whether the electronic expansion valve coil is correctly inserted.

3) Press the reset key (K3) of outdoor unit to check whether the same error appears.

- If it is the close error, operate the related indoor unit.

- If it is open error, put the related power off to check.

4) If there is no trouble for the above check items, replace the electronic expansion valve.

- Since the replacement of electronic expansion valve is the inconvenient work to recover the all refrigerant in the system,

be sure to check the above items before replacing it.

8-2-27. Electronic expansion valve open error

Outdoor unit display

Indoor unit display

Judgment method

Causes

(Open error of xth electronic expansion valve)

(Operation)

(Timer)

(Fan)

(Filter)

(Removing frost)

- Refer to the following judgment method

- Indoor unit electronic expansion valve open error

off

safety start

0 step

40 sec.

512 close 480 open

90 sec.

3 minutes

capacity control

0 step

Compressor

EEV(Wrong)

EEV(Normal)

Normal control according to the compressor

DB98-17816A(1)_8 3/2/04 9:35 AM Page 194

Содержание DVM Series







































































































































































































































































































































































































Результаты поиска

Содержание DVM Series

Отзывы:

Похожие инструкции для DVM Series

Бренды по названию

Популярные бренды

Samsung DVM Series, Руководство по обслуживанию

Результаты поиска

Содержание DVM Series

Отзывы:

Похожие инструкции для DVM Series

Бренды по названию

Популярные бренды