Samsung ACH1800E Скачать руководство пользователя страница 28

Страница: 28 / 150

4-9

Caution :

• Unless the address of digital switch of indoor unit PCB is set to “0” in case of “A” chamber single operation, the control by the wired

remote controller is disabled.

• The power of SET shall be put on again after the resetting of wired remote controller option so that the the set option can be applied.

Be sure to keep the power on/off of SET before and after the setting.

• The first digit of error code displayed during the single operation and group operation may be different. The first digit(MSB) stands for

the address of the set where the error occurs. Since it is the single operation, the address of SET is “0”.

4-2-4 Startup method by wired remote controller

Startup in case of the “A” chamber single
operation

• Put on the set power.
• Adjust the address of digital switch of indoor

unit PCB to “0”.

• Put ON the option switch(DS01) N02 of wired

remote controller PCB.

• Put on the set power.
• Press the test button of wired remote controller

for more than 3 seconds.

• The set is operated for 3 minutes by the forced

cooling operation and the set is off after 3
minutes.

• The error occurring during the test operation is

displayed on the wired remote controller
windows and it shall be referred to the
following table.

Samsung Electronics

4-9

Installation

Error Code

Meaning

Indoor unit room thermistor error

Indoor unit pipe thermistor error

Outdoor unit thermistor error

Float switch open error

Indoor unit

↔

outdoor unit communicating error

Wired remote controller

↔

indoor unit

communication error

Outdoor unit pipe thermistor error

Checking Area

• Indoor unit thermistor available or not and

disconnected

• Indoor unit PCB

• Indoor unit pipe thermistor
• Indoor unit PCB

• Outdoor unit thermistor
• Outdoor unit PCB

• Drain pump, float switch
• Drain system
• Dip SW2 of indoor unit main PCB

(If the drain pump is not installed, SW2 and
SW4 shall be at the Off position.)

• Indoor unit

↔

outdoor unit communicating

error

• Indoor unit

↔

outdoor unit communicating

cable

• Indoor unit PCB, Outdoor unit PCB

• Wired remote controller

↔

indoor unit

communication cable

• Indoor unit main PCB

• Outdoor unit pipe thermistor
• Outdoor unit PCB

00152-OIAIN-5 2/1/01 1:56 PM Page 4-9

Содержание ACH1800E























































































































































Результаты поиска

Содержание ACH1800E

Отзывы:

Похожие инструкции для ACH1800E

Бренды по названию

Популярные бренды

Samsung ACH1800E, Руководство по обслуживанию

Результаты поиска

Содержание ACH1800E

Отзывы:

Похожие инструкции для ACH1800E

Бренды по названию

Популярные бренды