Samsung ACH1800E Скачать руководство пользователя страница 14

Страница: 14 / 150

Samsung Electronics

3-3

Each time you press this button,
FAN SPEED is changed in the following order.

When the

indicator appeard on the remoconscreen, cleaning the air

conditioner filter. After that, press the this button.

FILTER SIGN

The ON Timer enables you to

switch on

the air conditioner automatically

after a given period of time that is from 30 minutes to 24 hours.
To cancel the On Time, press the (Set/Cancel) button.

The Off Timer enables you to

switch off

the air conditioner automatically

after a given period of time that is from 30 minutes to 24 hours.
To cancel the On Time, press the (Set/Cancel) button.

Each time you press this button
Mode is changed in the following order

Temp. down button. To decrease the temperature by the pressing
the temperature button

Temp. up button. To increase the temperatute by the pressing
the temperature button

FUNCTION OF KEY

: Auto Mode

: Blowing

: Cooling Mode

: Heat Mode

: Dehumidifying Mode

(DOWN)

Power On/Off button to start and stop airconditioner or timer set up

NAMED OF KEY

(UP)

Adjust air flow vertically.

3-2-2 Wireless Remote Controller

Operating Instructions and Installation

00152-OIAIN-5 2/1/01 1:55 PM Page 3-3

Содержание ACH1800E























































































































































Результаты поиска

Содержание ACH1800E

Отзывы:

Похожие инструкции для ACH1800E

Бренды по названию

Популярные бренды

Samsung ACH1800E, Руководство по обслуживанию

Результаты поиска

Содержание ACH1800E

Отзывы:

Похожие инструкции для ACH1800E

Бренды по названию

Популярные бренды