Samsung ACH1800E Скачать руководство пользователя страница 22

Страница: 22 / 150

4-3

Samsung Electronics

4-3

Installation

4-1-3 Appearance and function wireless receiving board

4-1-4 Opeartion specification of wireless receiving board

4-1-5 Wireless receiving board and outdoor unit PCB display specification when error occurs

PART NAME

DEFROST LAMP

FILTER SIGN LAMP

TIMER LAMP

ON-OFF LAMP

ON-OFF BUTTON

SOURCE & OPERATION SPEC.

RED, lamp on during defrost operation

Green, display during filter cleaning

Green, lamp when setting the reserve operation

Red, lamp during operation on

On/Off toggle operation

REMARK

in ERROR DISPLAY : flickering

in ERROR DISPLAY : filickering

in ERROR DISPLAY : flickering

in ERRO DISPLAY : flickerning

Operated only for automatic mode operation

ERROR MODE

(OUTDOOR DISPLAY)

CONTENTS OF ERROR

Abnormal on indoor temperature sensor
(4.9[V] and higher, 0.5[V] and lower

Abnormal on indoor pipe temperature sensor
(4.9[V] and higher, 0.5[V] and lower

Abnormal on outdoor temperature sensor
(4.9[V] and higher, 0.5[V] and lower

Float switch detection

Indoor

↔

outdoor communication defect

Indoor unit

↔

wired remote controller

communication defect

Abnormal on outdoor pipe temperature sensor
(4.9[V] and higher, 0.5[V] and lower

Reservation LED flickering
(1Hz period)

Operation LED and reservation
LED flickering (1Hz period)

Operation LED and filter LED
flickering (1Hz period)

Reservation LED and filter LED
alternating flickering (1Hz period)

Reservation LED and filter LED
flickering (1Hz period)

Operation LED and reservation
LED alternating flickering (1Hz
period)

Filter LED flickering (1Hz period)

REMARK

Restored when the indoor
temperature sensor is normal

Restored when the indoor pipe
temperature sensor is normal

Restored when the outdoor
temperature sensor is normal

Float switch detection

Re-detecting by operating off
signal after restoring

Restored when outdoor pipe
temperature sensor is normal

WIRELESS RECEIVING BOARD

DISPLAY (INDOOR UNIT)

Timer indicator

On/Off button

On/Off indicator

Removing frost
indicator

Filter Sign

indicator

Remote control sensor

00152-OIAIN-5 2/1/01 1:56 PM Page 4-3

Содержание ACH1800E























































































































































Результаты поиска

Содержание ACH1800E

Отзывы:

Похожие инструкции для ACH1800E

Бренды по названию

Популярные бренды

Samsung ACH1800E, Руководство по обслуживанию

Результаты поиска

Содержание ACH1800E

Отзывы:

Похожие инструкции для ACH1800E

Бренды по названию

Популярные бренды