background image

3

Instruction Manual

머리말

Precautions

안전하게 사용하기 위해서 필요한 경고사항을 본서에 기재했으니, 반드시 읽
어 주십시오. 문장 중의         마크는 특히 주의하여 주십시오. 산업용 기계
이므로 사용자 또는 이 장비를 사용하는 다른 사람에게 위험할 수 있는 항목
이나 조작에는 “안전 경고 기호” 를 사용하여 사용자의 주의를 환기시킵니
다. 안전 경고 기호로 표시한 지침을 잘 읽고 반드시 준수해 주십시오.

안전 경고 기호

Warning symbol

삼천리기계의 제품을 사용해 주셔서 진심으로 감사 드립니다.
본 취급설명서에 따라 제품의 사용방법을 바르게 이해하시고, 귀사의 생산에 
기여할 수 있도록 활용하여 주십시오.
또한, 알아두면 편리한 제품의 성능 등에 관하여 유의사항으로 설명해 두었
습니다. 본 취급설명서는 분실되지 않도록 항상 제품 가까이에 보관하여 주
십시오.

!

Thank you so much for choosing Samchully. Please read this manual 
carefully and fully understand the procedures for installation, operation, 
inspection and maintenance before operating the product.
Keep this manual handy as it contains detailed information on product 
functionality.

To ensure safe operation, please read this instruction manual and pay 
particular attention to the      symbol which emphasizes important 
information.

!

경고 용어

Warning term

!

DANGER

위 험

적절한 안전 절차와 지침을 준수하지 않으면 사망에
이르거나 중상을 입게 되는 매우 위험한상황을 나타
냅니다.

!

WARNING

경 고

적절한 안전 절차와 지침을 준수하지 않으면 사망에 이
르거나 중상을 입을 수 있는 잠재적으로위험한 상황을 
나타냅니다.

!

CAUTION

주 의

적절한 안전 절차와 지침을 준수하지 않으면 가벼운 상
처나 부상을 입을 가능성이 있는 잠재적으로 위험한 상
황을 나타냅니다.

IMPORTANT

유의사항

제품의 성능 및 오류나 실수를  막기 위한 지침입니다.

!

DANGER

!

WARNING

!

CAUTION

IMPORTANT

Indicates an imminently hazardous situation which, 
if not avoided, will result in death or serious injury. 
These warning messages include the preventive
actions that are indispensable to avoiding danger.

Indicates a potentially hazardous situation which,
if not avoided, will result in death or serious injury.
These warning messages include the preventive
actions that are indispensable to avoiding danger.

Indicates a potentially hazardous  situation which,
if not avoided, could result in minor injury or
machine damage.

Instructions for optimal performance and avoiding
errors or mistakes.

Содержание SR-200

























Отзывы: