background image

25

ZetrOZ, Inc.

Product Support 

203-349-2798

15.  Storage & Operating Conditions

15.1. STORAGE 

Store the 

sam

 Device in the following conditions: 

Temperature: 5-57 °C; 

Humidity: 10-80%; 

Atmospheric pressure range: 700-1060 hPa

Store the 

sam

 Ultrasound Coupling Bandages in the following conditions: 

Temperature: 5-30 °C; 

Humidity: 10-80%; 

Atmospheric pressure range: 700-1060 hPa

15.2. OPERATION

Only operate the 

sam

 Device in the following conditions: 

Temperature: 1-44 °C; 

Humidity: 10-80%; 

Atmospheric pressure range: 700-1060 hPa

Caution:  Do not keep the device in extreme hot or cold temperatures (above 50°C or 

below 0°C). Do not leave the 

sam 

Device in a hot or freezing car. Do not leave 

the device in direct sunlight for extended periods. UV light may damage or 
discolor the device.

16.  Disposal of Waste Products

sam

 Ultrasound Coupling Bandages are one time use and may be disposed of in 

regular sanitation trash. No special disposal procedures are necessary. 

Old, damaged or expired 

sam

 Power Controller Modules and applicators should be 

recycled or returned to the manufacturer for proper disposal. 

Содержание sam-12




































Отзывы: