Sam Cook 1197899, Руководство пользователя

Страница: 31 / 43

EN
30
of 5 for 5 seconds, and then changes to
speed 8 for 10 seconds and at the end,
the device is operati ng at H level of its
speed (maximum).
� A SOUP: Select this program to
process soups, the rotary speed starts
from 1 up to H within 9 seconds, and
then the appliance starts to operate
at maximum speed for 3.5 minutes.
� NUTS: Select this program to process
nuts, the rotary speed starts from 1
up to H within 5 seconds, and then the
appliance starts to operate at maximum
speed for 1 minute
� SAUCE: Select this program to process
sauce, the rotary speed starts from 1
up to 5 within 3 seconds, and then the
appliance starts to operate at speed 5
for 2.5 minutes
� SMOOTHIE: Select this program to
process smoothies, the rotary speed
starts from 1 up to H within 9 seconds,
and then the appliance starts to operate
at maximum speed for 1 minute.
C. START/STOP Press this butt on if you want
to start or stop the blender operati on.
D. PULSE Press and hold this butt on to set
your appliance to operate at maximum
speed.
It works in a pulse mode, only while you
hold this butt on.
E. SPEED +/- Butt ons to adjust speed (1-9 and
H, where H is the maximum speed)
F. TIME +/- Butt ons to adjust operati on ti me
(5 seconds-30 minutes every 5 sec) with a
sound signal to indicate the end of appli-
ance operati on
G. Indicators of Speed / Time / Program
selected.
To quickly increase or decrease the opera-
ti on speed/ti me, press and hold the butt on
to increase or decrease speed/ti me ("+" or
"-").
USING CUP BLENDER
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
NOTE! Do not put or remove the blender jug
while the appliance is running.
1. Place the blender housing ① on a dry, hard
and even surface.
2. Using the handle ③ , lift the blender
dome ② .
3. Aft er making sure that all blender jug parts
are assembled correctly, put the blender
jug ④ on the blender enclosure ① .
4. Cut the products into smaller parts to make
mixing easier. Put ingredients into the jug
only when the motor is stopped.
NOTE! Do not fi ll the jug above the mark of
2000 ml ④ .
5. Att ach the jug cover with cap. The cover in
the jug ⑥ should be depressed to the stop
whereas the cap ⑧ should be inserted with
tongues placed in grooves of the cover and
turned fully clockwise. Make sure the jug
cover handles are both sides of the appli-
ance aft er the assembly of the cover.
6. Close the blender dome ② .
7. Plug the appliance into the power supply
socket.
The appliance indicates the power supply
by a single beep and momentary illumina-
ti on of all functi on keys and a LCD display,
then the POWER (A) butt on starts lighti ng.
8. The appliance is ready for operati on.
9. Press the POWER (A) butt on. All functi on
butt ons and LCD display are highlighted.
The display will show the initi al setti ngs
(speed at level - 5, ti me - 20 sec)
10. The appliance can be acti vated in two ways:
in automati c or manual mode.
For the automati c mode and functi on selec-
ti on, press the butt on MENU . Each press of
the butt on changes the selected program.
Aft er selecti ng one of six programs, you
must press the butt on START .
The appliance starts up and performs
the selected program. You can stop the
appliance at any ti me by pressing the but-
ton STOP .
Manual mode starts with the selecti on of
the appliance operati on speed by pressing
butt ons SPEED , [+] and [-] to set the motor
rpm. Then by pressing butt on TIME select
the operati on ti me in the range from 5
to 30 min. Aft er selecti ng the rpm and
operati on ti me, press the butt on START .
The appliance starts up and performs the
selected operati on program. You can adjust
the operati on speed (rpm) while the appli-
ance is running.
You can stop the appliance at any ti me by
pressing the butt on STOP .
11. If you need to add ingredients when the
cup blender is running, remove the hole
plug (cap) from the lid (cover) and feed the
EN
31
ingredients through the hole, and then
replace the plug.
12. Aft er mixing the contents of the jug (when
the set program is fi nished or aft er pressing
the STOP butt on (C) , turn off the appliance
by pressing the POWER butt on (A) and pull
the power plug out of the electrical mains
socket.
ATTENTION! Before pouring out the content
of the jug wait unti l the knife stops rotati ng!
NOTE! Some products e.g. ice cubes should
be chopped using the PULSE functi on several
ti mes. To use the PULSE functi on, press and
and hold the PULSE butt on (D) . Do not start
the motor for more than 3.5 minutes, because
it may become over heated. Aft er these
3.5 minutes stop the appliance and wait unti l
it cools down.
INSTRUCTIONS FOR USE
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
1. To achieve the opti mum effi ciency, put the
required ingredients into the blender jug in
the following order: liquids, fresh ingredi-
ents, yoghurt and ice cream.
2. While operati ng maintain safe distance
from the appliance (min. 20 cm).
3. Before switching on the machine, always
press fi rmly the cover ⑥ , so you can freely
remove the cap ⑧ and put the ingredients
through the opening at the top of the cover
while mixing.
4. When processing hot drinks, start from low
speed and then go to high speed. When
there is too much food content inside the
blender jug, use PULSE as the fi rst functi on
to crush the products.
5. Every few seconds check the consistency
of the mixed ingredients.
6. Do not exceed the maximum permitt ed
working ti me of the appliance given in the
user manual.
7. If the motor stops, immediately fi nish mixing
or reduce the amount of ingredients in the
jug.
8. To grind ice cubes add a small amount of
water.
9. Do not remove the jug from the housing
when the appliance is in use.
10. Do not insert any objects into the jug
during mixing.
11. If food is pushed to the wall of the the jug
while mixing, this means that the speed
is too high and should be decreased. On
the other hand, if food is moving over the
blade, this means that the rotary speed is
too low and should be increased.
The appliance is equipped with an overload
safety switch ⑮ to protect the motor
against overload. If the appliance is over-
loaded, wait unti l the motor is cooled down,
press the butt on ⑮ to restart the appliance
and then turn on the appliance.
If the engine sti ll does not start, this
means that additi onal thermal protecti on is
acti vated - wait for some more ti me before
starti ng.
CLEANING AND MAINTENANCE
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
1. Before cleaning, make sure that the appli-
ance is switched off and disconnect it from
the power source.
2. Each ti me before and aft er using, disas-
semble the appliance and wash its parts in
warm water with detergent, rinse and dry
them thoroughly.
3. They should not be used in washing ma-
chines.
4. Cleaning the blender jug: fi ll the jug with
water, press PULSE butt on (D) for 10 sec-
onds and then turn it on and rinse with
water.
5. Use sponge or cloth to wipe the jug and
cover, dry them thoroughly to prevent gen-
erati ng odours or the growth of bacteria.
6. Periodically check all operati ng compo-
nents of the appliance before using them.
Do not use the blender if the blades got
stuck or rotate with diffi culty. Turn them
counter-clockwise to check if they operate