background image

12

6.

Press the 

Enter

 key to confirm the zero point again.

The scale goes through the start up routine and ends in normal 
weighing mode. 

If there is any error in the calibration, the scale will show 

CAL. Err

The scale will try to return to the previous step.

7.

If you have problems, press the 

On/Off

 key to exit the calibration mode 

and try the procedure again.

8.

Move the calibration switch back to normal weighing mode.

6.0

View Voltage and A/D Counts

You can view the battery voltage and A to D counts for diagnostic purposes. 
Follow these steps:

1.

With the calibration switch in the normal weighing mode and the scale in 
normal mode, press and hold the 

On/Off

 and 

Tare

 keys at the same time 

until the scale beeps…

Vol. X.X

 is displayed in the WEIGHT window, the word 

codE

 is 

displayed in the PIECE WEIGHT window and the A to D counts 
(code) is displayed in the COUNT window.

Vol. 

stands for voltage and 

X.X

 is the current voltage of the battery. If 

no battery is installed or the connection is not complete, 

Vol. 7.2 

will 

be displayed.

When the current working voltage is lower than 5.7V, the 

Low Batt

 

annunciator will light. 

When the voltage is lower than 5.5V, the 

Low Batt

 annunciator will 

light and the beeper will sound for approximately two minutes before 
the scale turns itself off.

The A to D counts for an empty scale should be between 5000 and 
100,000. This should be a positive number. The A to D counts for a 
scale at full capacity should be above 300,000. If the A to D counts 
are outside of these ranges or calibration and normal weighing 
cannot be done, your scale’s loadcell has been permanently 
damaged.

2.

To exit this mode, press the 

On/Off

 key…

The scale returns to normal mode.

Содержание B 120




















Отзывы: