Sakai SW352 Скачать руководство пользователя страница 147

Страница: 147 / 176

5-115

Disassembly and Assembly of Front Drum Assembly

7-2. Assembly of front drum assembly

1. Holder & vibrator shaft

1) On a hoist, stand the drum on the floor with

propulsion motor up.

See “Disassembly of front drum
assembly”, page 5-112.

2) Install bearing (23) to holder (20).

3) Install lock ring (24) in position.

2. Propulsion motor assembly

Using lifting bolts, lift the propulsion motor
assembly (18) and install it to the drum.
Tighten eight fixing bolts (17).

・

Tightening torque: 343 N·m (35 kgf·m)

★

Thoroughly clean the parts and remove burrs etc.

5) Using lifting bolts, mount holder (20) to the

drum.

4) With vibrator shaft (21) standing, assemble

holder (20) onto the shaft and install lock
ring (22).

TW5025036

TW5025035

TW5025037

Lifting bolt

TW5025032

Lifting bolt

Содержание SW352

















































































































































































Результаты поиска

Содержание SW352

Отзывы:

Похожие инструкции для SW352

Бренды по названию

Популярные бренды

Sakai SW352, Руководство по обслуживанию

Результаты поиска

Содержание SW352

Отзывы:

Похожие инструкции для SW352

Бренды по названию

Популярные бренды