Sakai SW352 Скачать руководство пользователя страница 136

Страница: 136 / 176

Removal and Installation of Engine and Propulsion/Vibration/Steering/Charge Pump Assembly

5-104

4. Removal and Installation of Engine and

Propulsion/Vibration/Steering/Charge Pump Assembly

4-1. Removal of engine and propulsion/vibrator/steering/charge pump

assembly

Disconnect the battery negative (–) cable.

TW5025007

TW5025008

TW5025009

2. Electric wiring

1) Disconnect connector (1), harness (2) and

propulsion pump solenoid valve wire
connector (3). Put the harness at a location
which does not hinder the work.

2) Disconnect wires at the engine that carry

oil pressure sensor, thermo sensor,
tachometer sensor and glow plugs.

3) Disconnect wires at the alternator and

starter.

See procedures under “Electric wiring of
alternator”, page 5-101 and “Electric
wiring of starter”, page 5-102.

3. Air cleaner

Disconnect air cleaner intake hose (4).

4. Radiator hose

1) Drain the coolant from the radiator.

2) Remove upper hose (5) and lower hose

(6).

1. Removal of engine hood

1) Remove the damper inside the hood.

2) Lift the hood and remove the hinge and

anti-fall arm. Take off the hood assembly.

3) Remove the front frame left side cover.

5. Throttle cable

Disconnect throttle cable (7) from the
governor lever. Unscrew nut (8) and detach
throttle cable at yoke (9).

6. Fuel hose

Disconnect fuel hoses (10) and (11).

Содержание SW352

















































































































































































Результаты поиска

Содержание SW352

Отзывы:

Похожие инструкции для SW352

Бренды по названию

Популярные бренды

Sakai SW352, Руководство по обслуживанию

Результаты поиска

Содержание SW352

Отзывы:

Похожие инструкции для SW352

Бренды по названию

Популярные бренды