Sakai SV410-2 Скачать руководство пользователя страница 142

Страница: 142 / 270

6-012

VIBRATORY DRUM • REAR AXLE

9) Lift and invert the drum with a crane. Stand it up

with the propulsion motor side upward.

Lifted weight in figure on the right

SV410D

-2

: 2,225 kg (4,905 lbs.)

SV410T

-2

: 2,425 kg (5,346 lbs.)

SV410TF

-2

: 3,765 kg (8,300 lbs.)

SV410TB

-2

: 2,425 kg (5,346 lbs.)

SV410FB

-2

: 3,765 kg (8,300 lbs.)

Inverting the drum can be dangerous work.

Therefore, be very careful, confirm that the

surrounding area is safe and work in a natural,

unstrained posture.

10) Remove the seventeen bolts (40).

As shown in the figure on the right, attach the

lifting bolt/nut (M20×2.5) to the holder (41) and

slowly lift. Remove together with the damper (42)

and disc (38).

Total of lifted parts (41, 42 and 38)

: 145 kg (320 lbs.)

11) Remove the eighteen bolts (48).

Remove the propulsion motor SUBASSY.

Propulsion motor SUBASSY

: 145 kg (320 lbs.)

•

SV410-2-06001

SV410-2-06002

Lift with crane

41
42

SV410-2-06002

Lift with crane

41
42

SV410-2-06003

Propulsion motor
SUBASSY

SV410-2-06003

Propulsion motor
SUBASSY

Содержание SV410-2















































































































































































































































































Результаты поиска

Содержание SV410-2

Отзывы:

Похожие инструкции для SV410-2

Бренды по названию

Популярные бренды

Sakai SV410-2, Руководство по ремонту

Результаты поиска

Содержание SV410-2

Отзывы:

Похожие инструкции для SV410-2

Бренды по названию

Популярные бренды