Sakai SV410-2 Скачать руководство пользователя страница 131

Страница: 131 / 270

6-003

VIBRATORY DRUM • REAR AXLE

2. VIBRATORY DRUM

2-1. Removal and Installation of Vibratory Drum

2-1-1. Removal of vibratory drum

1) Using the steering lock bar (1), connect the front

and rear frames. Firmly secure it so that the

front and rear frames do not move.

As shown in the figure on the right, lift the rear

frame with a crane. Firmly secure the vehicle

body by placing support stands and/or wooden

blocks at the rear end of the rear frame.

Do not allow the rear wheel tires to leave

the ground. (The tires must support the

vehicle’s body weight, too.)

Rear lift weight

SV410D

-2

: 3,800 kg (8,377 lbs.)

SV410T

-2

: 3,770 kg (8,311 lbs.)

SV410TF

-2

: 3,730 kg (8,223 lbs.)

SV410TB

-2

: 3,670 kg (8,091 lbs.)

SV410FB

-2

: 3,620 kg (7,981 lbs.)

When lifting the vehicle, use an appropriate

hoist of sufficient strength. Confirm that the

surrounding area is safe, and work in a natural,

unstrained posture.

Also, to firmly secure the vehicle body, use a

support stand of sufficient strength.

SV400-2-06001

SV400-2-06002

Lift with crane

Wooden
block

Support stand

SV400-2-06002

Lift with crane

Wooden
block

Support stand

Содержание SV410-2















































































































































































































































































Результаты поиска

Содержание SV410-2

Отзывы:

Похожие инструкции для SV410-2

Бренды по названию

Популярные бренды

Sakai SV410-2, Руководство по ремонту

Результаты поиска

Содержание SV410-2

Отзывы:

Похожие инструкции для SV410-2

Бренды по названию

Популярные бренды