background image

15

17

16

18

Securing the Stitch PRO  
Balance Wheel 

Remove the three screws (

A

) for the belt cover 

installation. Position the C-shaped belt guard 

(

B

) and reinstall the screws, making sure 

washers are positioned as shims behind the 

guard to keep it from being bent out of shape. 
Unscrew the reverse-threaded Posi-Pin

®

 nut 

(

C

). Slide the Stitch PRO Balance Wheel (

D

onto the bushing, making sure it does not 

interfere with the belt guard. If the wheel 

hits the guard, reposition the washers 

placed under the C-shaped belt guard 

or move the bushing out further by 

loosening the set screws in the bushing 

flange (

E

).

Push the Posi-Pin

®

 (

16

) through the 

hole in the balance wheel (

F

). While 

maintaining pressure on the Posi-Pin, 

rotate the balance wheel (

G

) until the 

Posi-Pin locks into one of the balance wheel 

bushing holes (

H

). Rotation of the balance 

wheel will now cause the machine to function. 
To disengage the machine (for bobbin winding), 

pull the Posi-Pin out of the balance wheel. The 

balance wheel will now rotate without operating 

the machine. Push the Posi-Pin into the hole at 

the center of the Posi-Pin nut (

I

) to store.

Belt Adjustment for the  
Workhorse

®

 Servo Motor 

Before installing the drive belt (

J

), loosen the 

screw (

K

) to allow the Workhorse Servo Motor to 

freely pivot. 
With the machine tilted back, slip the drive belt 

over the balance wheel track (

L

) and guide it 

onto the motor pulley (

M

) then carefully lower 

the machine. 
Pivot the motor back to tighten the belt. Proper 

adjustment of the belt results in 3/8 inch of slack 

when pressed by finger at its center. Retighten 

set screw (

K

). The Linkage Bar 

(

N

) may also 

need to be readjusted.
Once installed, the belt should not touch the 

table and should be centered on the track of 

both the balance wheel and motor pulley. Adjust 

the positioning of the motor left or right by 

loosening the bolts attaching the motor to the 

table. 
Once the motor is in the correct position and all 

bolts are tightened, tilt the machine back and 

remove the belt so the pulley bracket can be 

installed.
Before Continuing: See “Installing the Pulley 

Cover” in the Workhorse instructions.

A

H

C

G

D

I

F

N

M

K

J

L

B

E

 |    

Sailrite.com

Fabricator

®

 Assembly Instructions 

   |  8

Standard Fabricator

®

 Assembly 

Standard Fabricator

®

 Assembly

Содержание Fabricator
















Отзывы: