background image

11

12

13

14

Check Motor Rotation

The machine’s motor shaft should rotate counterclockwise when viewed from the motor shaft end. 

Plug in the motor, switch the power on and press down on the foot treadle to confirm operation now. 
If motor rotation is not counterclockwise, please refer to “Changing Motor Rotation” in the Workhorse

®

 

Installation Instructions.

Machine Installation

Push the machine Support Pin (

A

) into the hole 

in the tabletop nearest the carriage bolts holding 

the motor (

11

). 

Insert the tapered end of the knee lift post 

connector (

B

) into the raised hole in the bottom 

of the oil tray (

C

) (

12

).

Find the magnet for the oil tray (

D

) and place it 

in the bottom of the oil tray (

12

).

Take the rubber pads (

E

) off of the chrome 

hinges (

F

) and place them into their respective 

tabletop cavities (

G

). Insert the chrome hinges 

into the holes located on the back of the sewing 

machine (

H

).

With help, lift and lower the sewing machine into 

the tabletop so that the chrome hinges fit into 

the rubber pads (

13

).

Note: Do not cut away the string on the bottom 

of the machine; it is an oil wick. 

C

B

A

D

E

F

H

G

17  |    

Sailrite.com

Fabricator

®

 Assembly Instructions 

   |  18

Deluxe Fabricator

®

 Assembly 

Содержание Fabricator
















Отзывы: