manualshive.com logo in svg

SafetySpeed SPM301HD, Руководство пользователя

Поделиться
Скачать
SafetySpeed SPM301HD Скачать руководство пользователя страница 11

11

 

This  tool  must  only  be  wired  into  a  dedicated  circuit  that  has  a  short-circuit  protection  device  which  is  located 
ahead of the equipment in the circuit, in accordance with local codes. 

General guidelines are as follows: 

 SPM301; 110 Volt, Single Phase:  min. 20 Amp circuit protection. 

 SPM301HD; 208-230 Volt, Single Phase:  min. 20 Amp circuit protection.   

 SPM301NE; N/A*  

 Reference your Model/Serial Label (Pg. 2, Fig. 1) and your local codes before installation. 

*N/A = not applicable 

   

Electrical Connections 

The  SPM301  and  SPM301HD  screw  pocket  machine  variations  require  a  dedicated  circuit  that  meets  the 
requirements of the motors and local electrical codes. Connect the power cord from the dust collector to a circuit 
that meets the requirement of the dust collector and all local codes.  

Electrical connections should only be completed by a qualified electrician in accordance with all local 
codes. 

  

 
The 

SPM301

 requires a dedicated 110 Volt, 20 Amp circuit and includes a cord and plug.  

 
The 

SPM301HD

 requires a 20 Amp, 208-230 Volt, single phase dedicated circuit and cord.  A minimum 12/4 cord, 

to be connected to a plug or a disconnect is required.  The circuit must include a (N) neutral (common, white), two 
powered lines (L1 & L2), (red & black), and one (G) ground wire (green or yellow and green).  See wiring diagram 
below (Fig. 5) and inside electrical enclosure on the SPM301HD.  

  
                                                               

Figure 5:  Electrical connections SPM301HD 

L1 L2

G

N N

VFD

Electrical Supply Line 
Min. 12 ga. 4 wire 
(including ground) 
Will NOT run properly 
w/o 4 wire connection 
 
 
w/o 

L 1 - Hot, (black) 

L 2 

– Hot, (red)  

G 

– Ground, (green) 

N 

– Neutral, (white) 

Содержание SPM301HD





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды