manualshive.com logo in svg

Safe Fleet FRC inView 360 Fusion, Руководство по калибровке

Поделиться
Скачать
Safe Fleet FRC inView 360 Fusion Скачать руководство пользователя страница 8

© Safe Fleet | May 2018 | All rights reserved | Part #: 700-1111 R2

inView 360 Fusion Calibration Guide

p. 8

Placing Calibration Pads

Placing Calibration Pads

Once the AVM components have been installed, the next step is to place calibration pads around the vehicle.

Measure your vehicle length

Using a long tape measure, capture the length and width of the vehicle and record the 

values. These values will be used in the calibration software later on in the process. 

Place your calibration pads

1.  Start by placing measuring tapes in front of the vehicle, starting from the front of the tires and going forward 

(measuring tapes

 

 & 

). 

2.  Position tape

 

 squarely in front of the vehicle’s bumper. Use a square ruler to ensure that measuring tape 

 is 

perpendicular with tapes 

 & 

. The following values will help you determine where to place your calibration pads. 

Note: Measuring Proper Length   

 

 

 

          

The furthest tips of the vehicle should be considered in your measurement, includ-

ing the bumpers. However, external accessories like plows or winches should NOT 

be measured.

Содержание FRC inView 360 Fusion




























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды