SAF Lumina Series Скачать руководство пользователя страница 110

Страница: 110 / 123

CFIP Discovery Protocol

Discovery Protocol is Layer 3 Network protocol. This feature allows gathering information

from connected CFIP devices. The protocol discovers the IP address and software version of

connected CFIP unit. Discovery protocol uses UDP packets sent on port 78.

Discovery Protocol feature may be useful, when the IP address of connected device is

unknown and there is no possibility to establish connection through serial management port in order

to find out the IP address.

9.1

CFIP Unit Discovery Procedure

In order to discover the IP address and software version of CFIP unit proceed with the

following steps:

Connect your PC to CFIP unit through PoE injector

Download Discovery Protocol (available from saftehnika.com webpage in

„Download



Tools”

section (registration required))

Open the cmd window on your PC (Go to "Start->Run.." and enter "cmd")

Check for the IP address of your PC Ethernet adapter connected to CFIP unit by executing the

command "ipconfig"

Navigate to the folder containing previously downloaded and unzipped Discovery Protocol

using “cd” command

Now the necessary Discovery Protocol command can be executed (e.g. "dp sight

<scan_addr>", where <scan_addr> should be substituted by Ethernet adapter IP address of

your PC.)

Discovery Protocol Commands:

Discovery protocol commands

Command

Description

dp sight <local_addr>

Allows to find out the IP address and firmware version of CFIP unit

without knowing the IP subnet.

dp scan <local_addr>

<scan_addr>

This command gathers the information in the specified subnet. It

sends discovery packets to the broadcast address <scan_addr> and

returns the IP address and firmware version of CFIP unit.

dp remote <local_addr>

<remote_addr> <scan_addr>

Allows to find out the IP address and firmware version of CFIP

remote unit. This procedure allows bypassing routers as the

response packets are unicast packets.

The CFIP Lumina Series Full Outdoor Unit Technical Description and Configuration Guide • Rev. 1.10 •

© SAF Tehnika JSC 2013

Содержание Lumina Series




























































































































Результаты поиска

Содержание Lumina Series

Отзывы:

Похожие инструкции для Lumina Series

Бренды по названию

Популярные бренды

SAF Lumina Series, Руководство по настройке

Результаты поиска

Содержание Lumina Series

Отзывы:

Похожие инструкции для Lumina Series

Бренды по названию

Популярные бренды