background image

INTRODUCTION

 

DANGER 

– FAILURE TO FOLLOW THESE WARNINGS, INSTRUCTIONS, AND THE 

OWNER’S MANUAL MAY RESULT IN SERIOUS INJURY OR DEATH

CYCLONE IS DESIGNED AND MANUFACTURED FOR INSTALLATION AND USE ON INGROUND 
SWIMMING POOLS ONLY. DO NOT INSTALL THIS SLIDE ON ABOVE GROUND POOLS, 
HOUSEBOATS, BOAT DOCKS, FLOATING DOCKS OR PLATFORMS, OR OTHER BODIES OF 
WATER SUCH AS LAKES, PONDS, RIVERS, ETC. PROPER ASSEMBLY, INSTALLATION, USE, 
AND SUPERVISION ARE ESSENTIAL FOR PROPER OPERATION AND TO REDUCE THE RISK OF 
SERIOUS INJURY OR DEATH. 

ALL NATIONAL AND LOCAL BUILDING CODES MUST BE FOLLOWED. THIS INCLUDES ANY 
APPLIABLE REQUIREMENTS FOR SIZE OF CONCRETE FOOTING, OVERALL HEIGHT OF SLIDE, 
AND BODING OR ELECTRICAL CODES. 

CHECK INSIDE ALL BOXES AND PACKAGING MATERIALS FOR PARTS. BEFORE BEGINNING 
ASSEMBLY, READ ALL INSTRUCTIONS AND IDENTIFY PARTS USING THE FIGURES AND PARTS 
LISTED IN THIS DOCUMENT. IT IS CRITICAL THAT ALL PARTS BE CAREFULLY INSPECTED BY 
THE INSTALLER PRIOR TO INSTALLATION TO ENSURE THAT NO DAMAGE OCCURRED IN 
TRANSIT AND THAT A DAMAGED PART IS NOT USED. PROPER INSTALLATION CANNOT BE 
OVERSTRESSED, IMPROPER INSTALLATION VOIDS S.R. SMITH’S WARRANTY AND MAY 
AFFECT THE SAFETY OF THE USER. 

INSTALLER MUST GIVE TO SLIDE OWNER: CYCLONE 

INSTALLATION AND OWNER’S MANUAL, 

THE WARRANTY CARD, AND ANSWER ALL QUESTIONS REGARDING SAFE AND PROPER USE 
AND SLIDE MAINTENANCE. 

FOR COMPLETE SLIDE SAFETY 

INFORMATION REFER TO THE OWNER’S MANUAL. 

 

 

 

 

 

 

 

 

 

 

 

Содержание CYCLONE













Отзывы: