Ryobi RLT430CESB, Оригинальное руководство пользователя

Страница: 4 / 144

English
2
operating the product wear gloves to keep the
hands and wrists warm.
Ɣ
After each period of operation, exercise to increase
blood circulation.
Ɣ
Take frequent work breaks. Limit the amount of
exposure per day.
If you experience any of the symptoms of this condition,
immediately discontinue use and see your physician
about these symptoms.
INSPECTION AFTER DROPPING OR OTHER IMPACTS
Thoroughly inspect the product and identify any affections
or damage with it. Any part that is damaged should be
properly repaired or replaced by an authorized service
centre.
Ŷ
For damaged, loose or broken parts
Ŷ
For loose or damaged fasteners
Ŷ
Handles and hand guards
MAINTENANCE
WARNING
Use only original manufacturer’s replacement parts.
Do not use any attachments or accessories not
recommended by the manufacturer of this product.
Failure to do so may cause poor performance, possible
injury, and will void your warranty.
WARNING
Servicing requires extreme care and knowledge
DQG VKRXOG EH SHUIRUPHG RQO\ E\ D TXDOL¿HG VHUYLFH
technician. For service we suggest you return the
product to your nearest authorised service centre for
repair. When servicing, use only identical replacement
parts.
Ŷ
You may make adjustments and repairs described in
this user manual. For other repairs, have the product
serviced by an authorized service agent.
Ŷ
Consequences of improper maintenance may include
excess carbon deposits resulting in loss of performance
and discharge of black oily residue dripping from the
silencer.
Ŷ
The cutting attachment must not work in idle mode.
If this requirement is not satisfied, the clutch has to be
adjusted or the product needs an urgent maintenance
by a qualified technician.
Ŷ
After each use, clean with a soft dry cloth.
Ŷ
Check all nuts, bolts and screws at frequent intervals
for proper tightness to ensure the product is in safe
working condition. Any part that is damaged should be
properly repaired or replaced by an authorized service
centre.
Ŷ
When not in use, the product should be stored in a cool
dry place and locked up out of the reach of children. Do
not store outdoors.
LONG TERM STORAGE (1 MONTH OR LONGER)
Ŷ
Drain all fuel and/or oil from tank into a container
approved for fuel. Run engine until it stops.
Ŷ
Clean all foreign material from the product. Store it in
a well-ventilated place that is inaccessible to children.
Keep away from corrosive agents such as garden
chemicals and de-icing salts.
Ŷ
Abide by all ISO and local regulations for the safe
storage and handling of fuel. Excess fuel should be
used up in other engine powered equipment.
INTENDED USE
The product is only intended for use outdoors in a well
ventilated area.
The product is designed for cutting grass and light weeds
only in private garden areas.
The product is not allowed to be used in public gardens,
parks, sports centres or at roadsides as well as for
agricultural and forestry use.
The product should not be used to cut or trim hedges,
bushes or other vegetation where the cutting plane is not
parallel to the ground surface.
RESIDUAL RISKS
Even when the product is used as prescribed, it is still
impossible to completely eliminate certain residual risk
factors. The following hazards may arise in use and the
operator should pay special attention to avoid the following:
Ŷ
Injury caused by vibration. Always use the right tool for
the job, use designated handles and restrict working
time and exposure.
KNOW YOUR PRODUCT
See page 75.
1. Primer bulb
2. Choke lever
3. Fuel cap
4. Rear handle
5. Throttle trigger
6. Starter grip and rope
7. Trigger lock
8. On/off switch
9. Strap hanger
10. Front handle
11. Coupler
12. Knob
13. Grass deflector
14. Drive shaft housing