manualshive.com logo in svg

Ryobi RLT254CSEON, Оригинальное руководство пользователя, Страница: 9 / 16

Поделиться
Скачать
Ryobi RLT254CSEON Скачать руководство пользователя страница 9

9

English (Original Instructions)

automotive lubricant or 2-stroke outboard lubricant.

 

■

Mix 2% full synthetic 2-stroke lubricant into the petrol. 

This is a 50:1 ratio.

 

■

Mix the fuel thoroughly and also each time before 

fueling.

 

■

Mix in small quantities. Do not mix quantities larger 

than usable in a 30 day period. Full synthetic 2-stroke 

lubricant containing a fuel stabilizer is recommended.

FILLING THE TANK

 

WARNING

  Check for fuel leaks. If any are found, correct 

them before using the product to prevent fire or 

burn injury.

 

■

Stop the engine.

 

■

Clean surface around fuel cap to prevent 

contamination.

 

■

Loosen fuel cap slowly to release pressure and to 

keep fuel from escaping around the cap.

 

■

Carefully pour fuel mixture into the tank. Avoid spillage.

 

■

Prior to replacing the fuel cap, clean and inspect  

the gasket.

 

■

Immediately replace fuel cap and hand tighten. 

 

Wipe up any fuel spillage. Move 9 m away from 

refueling site before starting engine.

Note:

 It is normal for smoke to be emitted from a new 

engine during and after first use.

 WARNING

  Always shut off engine before fueling. Never add 

fuel to a machine with a running or hot engine. 

Move at least 9 m from refueling site before 

starting engine. Do not smoke!

9

STARTING AND STOPPING 

WARNING

 Never start or run the engine inside a closed or 

poorly ventilated area; breathing exhaust fumes 

can kill.

TO START A COLD ENGINE:

See Fig. 4a

NOTE: 

Lay the product on the ground. Ensure the cutting 

means will not contact anything when it starts to rotate.
1.  Press the primer bulb 10 times.

NOTE:

 After the 7th press, the fuel should be visible 

in the primer bulb. If not, continue pressing until the 

fuel is visible.

2.  Set the choke lever to   choke position.

3.  Hold down the throttle lock and then squeeze the 

throttle trigger completely and pull the starter grip until 

the engine attempts to start. Do not pull the starter 

grip more than 4 times. Keep the throttle trigger 

squeezed completely through steps 3 to 7.

4.  Set the choke lever to   choke position.

5.  Pull the starter grip until the engine starts. Do not pull 

the starter grip more than 6 times.

NOTE:

 If the engine does not start, repeat the 

procedure from step 2.

6.  Allow the engine to run for 10 seconds.

7.  Set the choke lever to   position.

TO START A WARM ENGINE: 

See Fig. 4b

NOTE: 

Lay the product on the ground. Ensure the cutting 

means will not contact anything when it starts to rotate.
1.  Press the primer bulb 10 times.

2.  Set the choke lever to

   

choke position.

3.  Hold down the throttle lock and then squeeze the 

throttle trigger completely and pull the starter grip until 

the engine starts. Do not pull the starter grip more 

than 6 times.

STARTING THE ENGINE USING AN ELECTRICAL 

STARTER (OPTIONAL)

WARNING

 Only use the Ryobi OES18 electrical starter. Use 

of any other starter may damage the engine and 

cause serious personal injury.

WARNING

 Before using the electrical starter to start the 

product, please read and understand completely 

1 Litre

+

20 ml

=

50:1 (2%)

2 Litres

+

40 ml

=

50:1 (2%)

3 Litres

+

60 ml

=

50:1 (2%)

4 Litres

+

80 ml

=

50:1 (2%)

5 Litres

+

100 ml

=

50:1 (2%)

Содержание RLT254CSEON

















Отзывы:

Нет отзывов