Ryobi RLT254CSEON Скачать руководство пользователя страница 5

5

English (Original Instructions)

 

checking for any damage if the product starts to 

vibrate abnormally

 

performing maintenance

 

WARNING

  Never use cutting means or attachments which 

are not specified by Ryobi  in this manual. This 

includes the use of metal multi-piece pivoting 

chains  and  flail-blades. These  items  are  known 

to break up during use and present a high risk of 

serious injury to the operator or bystanders.

 

WARNING

  Inspection after dropping or other impacts: 

Thoroughly inspect the product and identify 

any problems or damage to it. Any part that 

is damaged should be properly repaired or 

replaced by an authorised service centre.

TRIMMER SAFETY WARNINGS

 

Replace the string head if cracked, chipped, or 

damaged in any way. Be sure the string head is 

properly installed and securely fastened. Failure to do 

so can cause serious injury.

 

Avoid using on wet grass.

 

Do not walk backwards when using the product.

 

Walk, never run.

 

The small blade fitted to the cutting attachment guard 

is designed to trim the new extended line to the correct 

length for safe and optimum performance. It is very 

sharp; do not touch it, particularly when cleaning the 

product.

 

Always ensure that ventilation openings are kept clear 

of debris.

 

Before use and after any impact, check that there 

are no damaged parts. Examine the cutting means 

for signs of cracking or other damage. A defective 

switch or any part that is damaged should be properly 

repaired or replaced by an authorised service facility.

 

Make sure the head attachment is properly installed 

and securely fastened.

 

Make sure all guards, deflectors, handles, bolts, and 

fasteners are properly and securely attached.

 

Do not modify the product in any way. This may 

increase the risk of injury to yourself or others.

 

Use only the manufacturer’s replacement line in the 

cutting head. Do not use any other cutting attachment.

 

Never operate product without the cutting attachment 

guard in place and in good condition.

5

 

Maintain a firm grip on both handles while trimming. 

Keep string head below waist level. Never cut with 

the string head located over 76 cm or more above the 

ground.

 

The grass trimmer is fitted with a harness. Carefully 

adjust the harness to fit comfortably and help to 

support the weight of the machine at your right side. 

 

Identify the Quick Release mechanism and practice 

using it before you start using the product. Its 

correct use may prevent serious injury in case of 

an emergency. Never wear additional clothing over 

the harness or otherwise restrict access to the quick 

release mechanism.

TRANSPORTATION AND STORAGE

 

Stop the engine, and allow it to cool before storing or 

transporting.

 

Clean all foreign material from the product.

 

Drain all fuel from tank into a container approved for 

petrol. Remember to properly replace and tighten the 

fuel cap.

 

Run the engine until it stops, this will remove all fuel 

that could become stale and leave varnish and gum 

in the fuel system.

 

Store the product in a cool dry and well-ventilated 

place that is inaccessible to children. Keep away from 

corrosive agents such as garden chemicals and de-

icing salts. Do not store outdoors.

 

When transporting the product, secure it against 

movement or falling to prevent injury to persons or 

damage to the product.

 

Never transport the product while the engine is 

running.

 

Abide by all government and local regulations for the 

safety storage and handling of petrol.

SHORT TERM

 

Stop the engine, and allow it to cool before storing.

 

Clean all foreign material from the product.

 

Store the product in a cool dry and well-ventilated 

place that is inaccessible to children. 

 

Keep away from corrosive agents such as garden 

chemicals and deicing salts.

 

Do not store outdoors.

Содержание RLT254CSEON

















Отзывы: