manualshive.com logo in svg

Ryobi RLT254CSEON, Оригинальное руководство пользователя, Страница: 6 / 16

Поделиться
Скачать
Ryobi RLT254CSEON Скачать руководство пользователя страница 6

6

English (Original Instructions)

RESIDUAL RISKS

Even when the product is used as prescribed, it is still 

impossible to completely eliminate certain residual risk 

factors. The following hazards may arise in use and 

the operator should pay special attention to avoid the 

following:

 

–

Injury caused by vibration

Always use the right tool for the job, use designated 

handles and restrict working time and exposure.

 

–

Exposure to noise can cause hearing injury

Wear ear protection and limit exposure.

 

–

Eye injury due to flying debris

Wear eye protection at all times.

RISK REDUCTION

It has been reported that vibrations from handheld tools 

may contribute to a condition called Raynaud’s Syndrome. 

Symptoms may include tingling, numbness, and blanching 

of  the  fingers,  usually  apparent  upon  exposure  to  cold. 

Hereditary factors, exposure to cold and dampness, diet, 

smoking, and work practices are all thought to contribute 

to the development of the these symptoms. There are 

measures that can be taken by the operator to possibly 

reduce the effects of vibration:

 

■

Keep your body warm in cold weather. When operating 

the product, wear gloves to keep the hands and wrists 

warm. 

 

■

After each period of operation, exercise to increase 

blood circulation.

 

■

Take frequent work breaks. Limit the amount of 

exposure per day. 

If you experience any of the symptoms of this condition, 

immediately discontinue use and see your doctor.

 

WARNING

  Injuries may be caused, or aggravated, by 

prolonged use of a tool. When using any tool 

for prolonged periods, ensure you take regular 

breaks.

KNOW YOUR PRODUCT

1.  Primer bulb

2.  Choke lever

3.  Fuel cap

4.  Starter grip

5.  Throttle lock

6.  Ignition switch

7.  Throttle trigger

8.  Rear handle

9.  Front handle

10.  Shaft

11.  Grass deflector

12.  Reel Easy

TM

 string head

13.  Cutting line

14.  Idle speed screw

15.  Knob

16.  Hanger cap

17.  Clamp

18.  Screw

19.  Latch

20.  Wrench

21.  String head cover

22.  Bump knob

23.  Hex bolt

24.  Spool

25.  Spring

26.  String head housing

27.  Air box cover

28.  Air filter

29.  Combination wrench

30.  Spark plug

31.  Guide recess

32.  Button

33.  Metal spark plug boot

34.  Rubber protect boot

35.  Starter bit

36.  Electrical starter

37.  F/R switch

38.  Starter bit shaft 

39.  Shaft hole on the engine

40.  Switch button

41.  Line exit holes 

42.  Cutting line 

43.  Drive shaft 

44.  Quick release tab

45.  Pro Cut II™ string head

46.  Spool retainer

47.  Line load slots 

48.  Spark arrestor 

ASSEMBLY

UNPACKING

This product requires assembly.

 

■

Carefully remove the tool and any accessories from 

the box. Make sure that all items listed in the packing 

list are included.

 

■

Inspect the tool carefully to make sure no breakage or 

damage occurred during shipping.

 

■

Do not discard the packing material until you have 

carefully inspected and satisfactorily operated the tool.

 WARNING

 If any parts are damaged or missing, do not 

operate the product until the parts are replaced. 

Содержание RLT254CSEON

















Отзывы:

Нет отзывов