manualshive.com logo in svg

Ryobi RLT254CSEON, Оригинальное руководство пользователя, Страница: 14 / 16

Поделиться
Скачать
Ryobi RLT254CSEON Скачать руководство пользователя страница 14

14

English (Original Instructions)

20141119v2d1

PROBLEM

POSSIBLE CAUSE

SOLUTION

Engine starts, runs, and  

accelerates but will not idle.

Idle speed screw on carburetor 

requires adjustment

Contact a servicing dealer.

 Line will not advance.

1.  Line welded to itself.

1.  Lubricate with silicone spray.

2.  Not enough line on spool.

2. Install more line. Refer to "Line Replacement" earlier 

in this manual.

3.  Line worn too short.

3.  Pull lines while alternately pressing down on and 

releasing bump head.

4.  Line tangled on spool.

4.  Remove line from spool and rewind. Refer to "Line 

Replacement” earlier in this manual.

5.  Engine speed too slow.

5.  Advance line at full throttle.

Grass wraps round shaft 

housing and bump head

1.  Cutting tall grass at ground 

level.

1.  Cut tall grass from the top down.

2.  Operating the product at part 

throttle

2.  Operate the product at full throttle.

Bump knob hard to turn.

Screw threads dirty or 

damage.

Clean threads and lubricate with grease - if no 

improvement, replace bump knob.

Lubricant drips from muffler.

1.  

Operating the product at 

part throttle.

1. Operate the product at full throttle.

2. Check lubricant/fuel mixture.

2. Use fresh fuel and correct synthetic 2-stroke lubricant 

mix.

3. Air filter dirty.

3. Clean per instruction in "Maintenance" section.

Содержание RLT254CSEON

















Отзывы:

Нет отзывов