manualshive.com logo in svg

Ryobi RLT254CSEON, Оригинальное руководство пользователя, Страница: 7 / 16

Поделиться
Скачать
Ryobi RLT254CSEON Скачать руководство пользователя страница 7

7

English (Original Instructions)

Failure to heed this warning could result in 

serious personal injury.

 WARNING

  Do not attempt to modify the product or create 

accessories not recommended for use with the 

product. Any such alteration or modification is 

misuse and could result in a hazardous condition 

leading to possible serious personal injury.

 WARNING

  To prevent accidental starting that could cause 

serious personal injury, always disconnect the 

engine spark plug wire from the spark plug when 

assembling parts.

 

WARNING

  Never attach or adjust any attachment while 

power head is running. Failure to stop the engine 

may cause serious personal injury.

 

WARNING

  Be certain the knob is fully tightened before 

operating equipment; check it periodically for 

tightness during use to avoid serious injury.

PACKING LIST

 

■

Trimmer

 

■

Trimmer attachment shaft

 

■

Front handle assembly

 

■

Grass deflector

 

■

Reel Easy

™

 string head

 

■

Pro Cut II

™ 

string head

 

■

Shoulder strap

 

■

Cutting line

 

■

Combination wrench

 

■

Manual

 

■

Figure sheet

 

■

Engine oil

 

■

Wrench

ATTACHING THE FRONT HANDLE

See Fig. 2a

 

■

Remove the securing screws and clamp from the front 

handle. 

 

■

Align the hooks on the clamp into upper shaft slot. 

 

■

Install the front handle onto the upper shaft. 

NOTE: 

The front handle should tilt slightly towards the 

operator when correctly fitted. 

 

■

Place the securing screws through the front handle 

and securely tighten them into the captive nuts on the  

front handle. 

7

NOTE: 

Do not attempt to remove the locks on the clamp, 

the locks limit the upper position of the front handle 

ATTACHING THE GRASS DEFLECTOR

See Fig. 2b

 

■

Stop the engine.

 

■

Loosen the lock nut.

 

■

Insert the shaft into the grass deflector.

 

■

Tighten the lock nut.

ATTACHING THE POWER HEAD TO TRIMMER 

ATTACHMENT

See Fig. 2c

 

WARNING

  Never attach or adjust any attachment while power 

head is running. Failure to stop the engine may 

cause serious personal injury.

 

■

Stop the engine.

 

■

The trimmer attachment connects to the power head 

by means of a coupler device.

 

■

Loosen the knob on the coupler of the power head 

shaft and remove the end cap from the attachment.

 

■

Push in the button located on the attachment shaft.

 

■

Align the button with the guide recess on the power 

head coupler and slide the two shafts together.

 

■

Rotate the attachment shaft until the button locks into 

the positioning hole.

NOTE:

 If the button does not release completely in the 

positioning hole, the shafts are not locked into place. 

Slightly rotate from side to side until the button is locked 

into place.

 

■

Tighten the knob securely.

REMOVING THE ATTACHMENT FROM THE POWER 

HEAD

 

■

Loosen the knob.

 

■

Push in the button and twist the shafts to remove and 

separate the ends.

INSTALLING THE REEL EASY™ STRING HEAD

See Fig. 2d

 

■

Stop the engine.

 

■

Open the Reel Easy

TM

 string head by depressing the 

latches on each side. The contents of the string head 

are spring loaded, so keep your other hand over the 

string head cover while depressing the latches.

Содержание RLT254CSEON

















Отзывы:

Нет отзывов