Ryobi EMS-1830SC, Руководство пользователя

Страница: 32 / 270

BASIC SAW OPERATIONS
DANGER
Never lower the saw completely in front of the
work-piece and then cut only on the forward
push. The upward moving rear portion of the
blade could twist the workpiece from your grasp.
Workpieces up to 342.9 mm wide and 88.9 mm thick can
be cut following the directions below:
■
Put wood against fence and secure with clamp as
appropriate.
■
Loosen the slide lock knob.
■
Grasp the saw handle and pull the carriage until the
arbor (center of saw-blade) is over the front edge of
the workpiece.
■
Switch on the saw and allow to come to full speed.
■
Push the saw handle all the way down and cut
through the leading edge of the workpiece.
■
Gently push the saw handle towards the fence
completing the cut.
■
Push power head to full rear position after each cut.
■
Turn motor off and allow blade to come to a complete
stop before moving hands.
CHOP CUTTING (FIG. 20)
■
Slide the cutting head to the rear as far as it will go.
■
Lock slide lock knob.
■
Position workpiece on table and against fence and
secure with clamp as appropriate.
■
Turn on saw and lower blade into work-piece.
■
After cut is complete turn off saw, allow blade to stop
rotating before allowing cutting head to rise up.
BODY AND HAND POSITION
■
Never place hands near cutting area. Place hand at
least 100 mm from path of blade.
■
Hold workpiece firmly to the fence to prevent
movement toward the blade.
■
When holding the workpiece to the left side of the
blade, always use your left hand. Use your right hand
to hold the workpiece to the right side of the blade.
■
Before making a cut, make a “dry run” with the power
off so you can see the path of the blade.
■
Keep hands in position until trigger has been released
and the blade has completely stopped.
WARNING
Do not try to cut short pieces, you cannot properly
support the workpiece and keep your hold down
hand the required distance from the blade.
MITER CUT (FIG. 21)
When a miter cut is required, move the saw to the
desired angle. Move with the handle to the miter angle to
make the cut. There are settings on the miter scale for
angles (degrees) and crown molding.
Note: Remember to unlock the miter lock lever before
changing the miter angle.
BEVEL CUT (FIG. 22)
When a bevel cut is required tilt the blade to desired bevel
angle. Stand to the left side of the handle to make the cut.
SLIDING FENCE
When beveling the blade to the left or back fence may
have to be repositioned. Loosen the fence locking knob
and slide the fence to the left or right as needed. Adjust
the fence as close to the guard as possible to provide
maximum support for the workpiece. Securely tighten
knob and make a dry run with the saw off to check for
clearance between the fence and guard. On certain
extreme compound cuts it may be necessary to remove a
sliding fence to avoid interference. After completing bevel
cut(s) remember to replace and/or slide the fence back.
VERNIER BEVEL SCALE OPERATION
The Vernier bevel scale can quickly and accurately help
the user to adjust the saw to any 1/2° increment as
illustrated (Fig. 16).
COMPOUND CUT
When a compound cut is required, select the desired
bevel and miter positions.
CUTTING BOWED MATERIAL (FIG. 23)
Before cutting a workpiece, check to make sure it is not
bowed. If it is bowed the workpiece must be positioned
and cut as illustrated. Do not position workpiece
incorrectly or try to cut the workpiece without the support
of the fence. This will cause pinching of the workpiece on
the blade. The workpiece could suddenly jump or move
and your hand could hit the blade.
26
GB
F D E
English
I P NL S DK N FIN GR H CZ RUS RO PL
EMS-1830SC manual 14/05/04 12:26 Page 26