background image

V1.0 

Rungu Taillight Installation and Operation 

Copyright 2017 Standard Bearer Machines, LLC 

 

Page 

15

 of 

15

 

Operating the taillight 

The Rungu Taillight by GUB has 5 operating modes all accessed by pressing the button power button in 
the center of the taillight.  

 

Turning the taillight on and off 

Press the power button in the center of the taillight to turn on the taillight.  Press and hold down the 
power button for three seconds t

o turn off the taillight. The taillight automatically turns off if it doesn’t 

sense motion after a few minutes.  

Taillight operating modes 

There are five different taillight settings and each one can sense braking to illuminate brighter just like a 
brake light in a car. Each time you press the button in the center of the taillight for one second after 
turning on the taillight changes the way the taillight operates. After the fifth press of the button, the 
taillight returns to the default mode.  In this way you can cycle through all five modes. 

Mode 

Button press 

Description 

Brake light 1 

Default/turn 
on/full cycle 

Taillight illuminates at lowest brightness and then gets three times 
brighter when sensing braking/deceleration 

Brake Light 2 

One 

Taillight illuminates brighter and then gets three times brighter 
when sensing braking/deceleration 

Flashing 1 

Two 

Taillight flashes approximately once/second 

 illuminates brighter 

when sensing braking/deceleration 

Flashing 2 

Three 

Taillight flashes rapidly

 illuminates brighter when sensing 

braking/deceleration 

Pulsating 

Four 

Taillight pulsates 

 illuminates brighter when sensing 

braking/deceleration 

 

Содержание Taillight
















Отзывы: