Operation
42
Crystal Series LCD Installation/Operation Manual
PRE
L
IMINAR
Y
ISF Calibration
Use the ISF Calibration menu to perform advanced picture quality adjustments.
This
menu should be used by ISF-certified technicians only.
Picture Adjust:
The controls in this menu are identical to those in the main Picture Adjust
menu, but are accessible only by entering the ISF Calibration menu passcode. This makes
it possible to restore the picture quality settings to what they were when the Crystal Series
LCD was installed, simply by recalling the “ISF Night” or “ISF Day” preset.
• Brightness:
Refer to
Brightness
on page 33.
• Contrast:
Refer to
Contrast
on page 34.
• Color:
Refer to
Color Saturation
on page 35.
• Tint:
Refer to
Tint
on page 35.
• Sharpness:
Refer to
Sharpness
on page 36.
• ADC Phase Adj.:
This control works similarly to the Phase adjustment for RGB signals
(refer to
Phase
on page 39). Use it to improve the apparent sharpness of 720p and
lower-resolution Component, S-Video or Composite sources. For best results, adjust
ADC Phase while displaying a “Sharpness” pattern (Figure 4-5).
• DNR:
Refer to
DNR
on page 36.
• MPEG NR:
Refer to
MPEG NR
on page 36.
• Backlight:
Refer to
Backlight
on page 36.
• Color Temp.:
To choose a color temperature setting, select Color Temp. from the
Picture Adjust menu and press
ENTER
. (Color temperature defines the “color of gray.”)
The choices are
5400K
,
6500K
,
8500K
and
Custom
. The default setting,
6500K
, is
appropriate for most situations. Higher settings produce a “bluer” picture; lower ones
impart a reddish hue to the image.
Each color temperature setting has six (6) “white balance” parameters associated with
it (two each for red, green and blue). (The White Balance settings for the 5400K, 6500K
and 8500K color temperatures are factory-set and cannot be changed.)
• Gamma:
Refer to
Gamma
on page 37.
• Save Settings:
For each input and supported resolution, the Crystal Series LCD lets
you save image quality settings as presets that you can recall at a later time. You can
create up to three presets – designated “Custom,” “ISF Day” and “ISF Night” – per
input and resolution.
You should save changes to any of the following settings to a preset; otherwise they
will be lost when a new input source or resolution is selected:
• Brightness
• Contrast
• Color saturation
ISF Calibration
Picture Adjust
White Balance
CMS Hue
CMS Saturation
CMS Luminance
Blue Enable
Factory Reset
Splash Duration
➤
You must enter a passcode to access the ISF Calibration menu.
To create a “Custom” color temperature, select Custom from the
Color Temp. menu and press
ENTER
. Then, press
ENTER
a
second time to go directly to the White Balance menu. (This shortcut
is available only from the ISF Calibration menu.)
Note
Tip
Содержание Crystal CX-42HD
