RuggedCom RuggedServer RS910 Скачать руководство пользователя | Manualshive

Страница: 19 / 27

background image

19



2007 RuggedCom Inc. All rights reserved

Rev100

RuggedCom also does not recommended to use these ports to interface to field devices across
distances which could produce high levels of ground potential rise, (i.e. greater than 2500V) during
line to ground fault conditions.

4.2 Fiber Optic Ethernet Ports

Depending on the order code of the product, the RS910 can be equipped with several different
fiber optic ports. The Transmit (Tx) and Receive (Rx) connections of each port must be properly
connected and matched for proper link and operation. The drawings in the following figures show
each fiber optical connector style with a side and top view to allow the user to identify the proper
cable connection orientation.

Figure 14: 10FL ST connector

Figure 15: 100FX MTRJ connector

Figure 16: 100FX ST connector

Figure 17: 100FX LC connector

Figure 18: 100FX SC connector

4.3 Ethernet Panel Description

Each Ethernet and Serial port, excluding RJ45 Ethernet on port 9, is equipped with one LED that
indicates link/activity status information. The LED will be solid for ports with link, and will blink for
activity. The diagram in Figure 19 highlights the port and the associated link/activity LED. RJ45
Ethernet port on port 9 consists of two LEDs and the table below shows the LED description.

«
...
17
18
19
20
21
...
»

Содержание RuggedServer RS910




























Отзывы:

Нет отзывов

Похожие инструкции для RuggedServer RS910

TokenLink Velocity 3C319

Бренд: 3Com Страницы: 2

Бренд: Aastra Страницы: 2

Бренд: H3C Страницы: 33

S5500-SI Series

Бренд: H3C Страницы: 1217

Бренд: 3Com Страницы: 2443

Бренд: H3C Страницы: 3

Бренд: H3C Страницы: 4

Бренд: Juniper Страницы: 502

Бренд: TP-Link Страницы: 73

Бренд: Edgewater Networks Страницы: 7

Active Module Carrier VX402C-64

Бренд: C&H Страницы: 32

SmartMesh IA-510 D2511

Бренд: Dust Networks Страницы: 30

Бренд: Draytek Страницы: 2

Бренд: Genie Страницы: 6

Бренд: Abocom Страницы: 63

Бренд: Westermo Страницы: 34

Бренд: Airvana Страницы: 90

CyberPower RMCARD201

Бренд: CyberPower Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды